Magnetic resonance imaging needs a magnetic field strength of 1.5 T. The solenoid is 1.8 m long and 75 cm in diameter. It is tightly wound with a single layer of 2.10-mm-diameter superconducting wire. Part A You may want to review (Pages 810 - 814) What current is needed? Express your answer with the appropriate units. HÁ Value Units Submit Request Answer

Magnetic resonance imaging needs a magnetic field strength of 1.5 T. The solenoid is 1.8 m long and 75 cm in diameter. It is tightly wound with a single layer of 2.10-mm-diameter superconducting wire. Part A You may want to review (Pages 810 - 814) What current is needed? Express your answer with the appropriate units. HÁ Value Units Submit Request Answer

Inquiry into Physics

8th Edition

ISBN:9781337515863

Author:Ostdiek

Publisher:Ostdiek

Chapter8: Electromagnetism And Em Waves

Section: Chapter Questions

Problem 9Q

See similar textbooks

Similar questions

Q1: find the frequency cyclotron (F) of free electron, if the magnetic field about 1KG applied on the conductor sheet?
WHY does larmor frequency depend on the external magnetic field strength? I want an explanation of why.
Band Resistor color coding, and solve any three examples of your choice?
Assuming that the current is 1A and radius of the circular path of the electron is 4.9 What is the magnetic field where the electrons are traveling that results from this 1 A current in the Helmholtz coils? Hint: Evaluate the expression given for the field betwee two Helmholtz coils with the dimensions used in the experiment. Provide a numerical answer with no units, simply the field in "microtesla", that is in 10-6 T. For example, if you found 3.4 x 10-4 T, answer "340".
The deflector plates of a Thomson appliance are 6.0 cm long and separated by 1.2 cm. The distance between the front edge of the plate and the tube is 30.0 cm. The energy assigned to the electrons of the beam is 2.8 keV (can make an illustration for a good understanding) (a) If the potential of 25 V is applied to the deflector plates, what will be the deviation of the beam on the screen? (b) Find the module of the crossed magnetic field that would allow the beam to pass through the plates, without suffering any deviation. Answer a) 7.36 mm b) 6.64 x 10^ - 5 T
The Hall effect is to be used to find the density of charge carriers in an unknown material. A Hall voltage 40 V for 3-A current is observed in a 3-T magnetic field far a rectangular sample with length 2 cm, width 1.5 cm, and height 0.4 cm, Determine the density of the charge carriers.
Using the given charge-to-mass ratios for electrons and protons, and knowing the magnitudes of their charges are equal, what is the ratio of the proton's mass to the electron's? (Note that since the charge-to-mass ratios are given to only three-digit accuracy, your answer may differ from the accepted ratio in the fourth digit.)
(I) A galvanometer needle deflects full scale for a 53.0µAcurrent. What current will give full-scale deflection if themagnetic field weakens to 0.760 of its original value?
What is the direction of the magnetic field that produces themagnetic force on a positive charge as shown in each of thethree cases in the figure below, assuming B is perpendicularto v ?
A low-power laser used in a physics lab might have apower of 0.50 mW and a beam diameter of 3.0 mm. Calculate (a) the average light intensity of the laser beam, and(b) compare it to the intensity of a lightbulb producing100-W light viewed from 2.0 m.
Show your solutions An air-core solenoid having 4000 loops is 120 cm long and has a diameter of 4 cm. If a current of 10 A is sent through it, what will be the magnetic field formed within it?
A mass spectrometer is being used to monitor air pollutants. It is difficult, however, to separate molecules with nearly equal mass such as CO (28.0106 u) and N2 ( 28.0134u). How large a radius of curvature must a spectrometer have (Figure 1) if these two molecules are to be separated on the film by 0.65 mm ?