Masonry brickwork has a density of 116 Ib/ft. Determine the maximum height(FT) of abrick wall if the allowable compressive stress is limited to 141 lb/in?. and the brick is 4.7in. thick and 5.9 in. wide.Answer in two decimal places. Numerical values only. Don't indicate units here, just on thesubmitted solution.

Answered: Image /qna-images/answer/d36b6f07-adc4-41f1-b2ed-202a60590eb7.jpg

Masonry brickwork has a density of 116 Ib/ft. Determine the maximum height(FT) of a brick wall if the allowable compressive stress is limited to 141 Ib/in?. and the brick is 4.7 in. thick and 5.9 in. wide. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.

Masonry brickwork has a density of 116 Ib/ft. Determine the maximum height(FT) of a brick wall if the allowable compressive stress is limited to 141 Ib/in?. and the brick is 4.7 in. thick and 5.9 in. wide. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter5: Measuring Concrete Work

Section: Chapter Questions

Problem 4RQ: What size does an opening in concrete have to be before a deduction is made from the volume of...

See similar textbooks

Similar questions

g. Minimum width B (in meter) of wall to be safe against overturning if factor of safety against overturning is 1.5 (minimum). Consider 24 kN/m3 as the unit weight of concrete. B = Note: Round your answer to three decimal place. Thankyou
B: calculate mortar for a wall which height is 10 feet, length is about 14 and width 9 inch?
Module 5 Base on the given plan below. Estimate the materials needed for external masonry works only. Assume wall height to be 3.0 m openings at: a. common area Doors (0.9x2.1), windows (1.2x1.2) b. t&b windows (0.6x0.6) c. Vertical reinforcement at 80cm O.C. d. Horizontal reinforcement at every 3 layers. e. Use Class B mortar and Class B mixture for plastering. f. Assume 12mm thick of mortar per layer g. 12mm thick for plastering
Q: Demonstrate various steps of application of (1) Lime plaster and (2) Stucco plaster on a masonry wall.
. A concrete masonry unit has actual gross dimensions of 7-5/8 inch.*7-5/8 inch.*7-5/8inch. The unit is tested in a compression machine with the following results:Failure load=110 kipsNet volume of 366.2 inch3a. Calculate the gross area compressive strength. b. Calculate the net area compressive strength.
d) How many square meters of the wall will be applied with fineplaster?e) What is the rebar factor to be used per square meter forestimates of rebars required for the CHB wall? (unit should bem/m2)f) What is the total number of cement bags required for mortarand plaster (both rough and fine)?
Masonry brickwork has a density of 148 lb/ft3. Determine the maximum height(FT) of a brick wall if the allowable compressive stress is limited to 144 lb/in2. and the brick is 5.0 in. thick and 6.1 in. wide.
What size does an opening in concrete have to be before a deduction is made from the volume of concrete to account for the opening?
What is the main value in pre-stressing pre-cast concrete columns?
A concrete masonry unit has actual gross dimensions of 190 mm X 190 mm X190 mm. The unit is tested in a compression machine with the followingresults:Maximum failure load = 370 kNNet volume = 5125 cm3a. Is the unit categorized as solid or hollow? Why?b. Calculate the gross area compressive strength.c. Calculate the net area compressive strength.
When should a modification in the consistency of the fresh concrete be made?
A concrete masonry unit has actual gross dimensions of 7-5/8” * 7-5/8” * 7-5/8”. The unit istested in a compression machine with the following results:Max. Failure load = 83 kipsNet volume = 312.7 in3a) Is the unit categorized as solid or hollow? Why?b) Calculate the gross area compressive strength.c) Calculate the net area compressive strength.