Match the diagram with its purpose Indicates how a circuit is wired physically Choose. Shows the sequence of a system without too much technical details Choose. Block diagram Circuit or Schematic diagram Layout diagram Wiring diagram As the IEE regulations, in a TT earthing system, the loop impedance (Ze) should not exceed the maximum limit of per O 21 O 0.35 O 50 O 0.8 Capacitive circuit is the main cause for the low power factor. Select one: O True O False

Match the diagram with its purpose Indicates how a circuit is wired physically Choose. Shows the sequence of a system without too much technical details Choose. Block diagram Circuit or Schematic diagram Layout diagram Wiring diagram As the IEE regulations, in a TT earthing system, the loop impedance (Ze) should not exceed the maximum limit of per O 21 O 0.35 O 50 O 0.8 Capacitive circuit is the main cause for the low power factor. Select one: O True O False

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter6: Ground-fault Circuit Interrupters, Arc-fault Circuit Interrupters, Surge Protective Devices, Immersion Detection Circuit Interrupters, And Appliance Leakage Current Interrupters

Section: Chapter Questions

Problem 18R

See similar textbooks

Similar questions

Briefly explain TNC-S earthing scheme as applied to earthing system design. (Hint: Support your answer with a well labelled diagram).
c.1. Which of the following is one of the three essential functions of an equipment grounding conductor?A. Provide an arc-fault current pathB. Establish groundingC. Establish bondingD. Ensure the system is groundedc.2. What's another name for the three-point method of Earth resistance testing?A. Fall-of-potentialB. Line surgeC. Spatial shieldingD. Leakage current c.3. If the National Electrical Code provides a requirement to ground equipment, it generally implies thatthere will be a direct connection to the Earth of a connection through a/anA. grounding electrode conductor.B. equipment grounding conductor.C. equipotential bonding conductor.D. bonding conductor.
2.a. What's defined as an assembly consisting of a service raceway, guy wires or braces, service head, andany fittings necessary for the termination and support of overhead service conductors?A. Drip loopB. Service lateralC. Service dropD. Service mast 2.b. What's likely to happen when connected parallel conductors are different lengths?A. An NEC violationB. Misidentification of conductor cablesC. An uneven distribution of currentD. Conductor termination
9. Which grounding method is typically required of higher-voltage systems? A. Grounding through inductorsB. Grounding through a low amount of resistanceC. Grounding through a high-impedance device D. Grounding through surge arresters 10. Which term relates to the conductors connected to the output side of a separately derived system? A. Neutral conductorB. Transformer secondary conductorC. System conductor D. Derived phased conductor 11. If there's no service disconnect at a remotely supplied building, then the grounding electrode conductor and the equipment grounding conductor can be bonded together at a A. junction box.B. structural steel location. C. grounding electrode rod. D. water line. 12. In a DC system, the bonding jumper between the negative of the supply and ground is normally made at the source or at the A. first disconnecting means. B. first device on the supply. C. end of the DC line.D. entrance to the building. 13. Which of the following is a common raceway…
10.a. Imagine that you're installing the electrical service to a pool. In this situation, any electrical equipmentwithin _______ feet of the pool must be grounded.A. 6B. 12C. 9D. 510.b. The installation of an intersystem bonding termination has been a National Electrical Code requirementsinceA. 2008.B. 2014.C. 2017.D. 2005.
The following problems refer to grounding requirements. Give the source of yourresponses. 1. What is the minimum size copper grounding electrode conductor for a service withthree sets of parallel 350 kcmil conductors (three conductors per phase)?
Please explain the purpose of the following LabView block diagram structures
16. Flexible metal conduit will be installed between a raceway and a transformer in a system. If it's to serve as an equipment grounding conductor, the flexible conduit and its fittings must be less than _______ feet. A. 2 B. 6 C. 10 D. 4 17. In which of the following situations can an equipment ground conductor be run separately from the circuit conductors? A. When you install a GFCI and are connecting additional receptaclesB. When the connection is to be made to a nearby water pipeC. When you're replacing an ungrounded two-wire receptacle with a grounded receptacle D. When there are no spare conductors in the cable 18. A 400-amp circuit breaker protects a feeder that's installed in a nonmetallic raceway that requires an equipment grounding conductor. Which of the following is the minimum size of aluminum equipment grounding conductor that should be used in this situation? A. No. 4B. No. 1C. No. 6 D. No. 2 19. Which of the following is bonded to the grounding electrode system…
The voltage drop percentage for a panel feeder with a no continuous load of 180A, using 3/0 THWN copper conductors at 480V, three-phase, and a length of 248' is
A Type NM cable carries a branch circuit to the outside of a building, where it terminates in a metal weatherproof junction box. From this box, a short length of EMT is installed upward to another metal weatherproof junction box on which is attached a cluster of outdoor floodlights. The first box is located approximately 24 in. (600 mm) above the ground. To Meet Code, do the metal boxes and metal raceway have to be grounded? Yes _______________ No _______________ NEC _______________.
a. What is the ampere rating of circuit A16? _________________ b. What is the conductor size of circuit A16? _________________
Which of the following statements Meets Code? (Circle the correct answer.) a. Hydromassage tubs and all of their electrical components shall be GFCI protected. b. Hydromassage tubs and all of their electrical components shall not be GFCI protected.