Material Needed: 2- IN4001 Silicon Diodes 1- 1K resistor 1 - 10K resistor 1k Ohm (A) IN4001 ELECTRONIC WORKBENCH OUTP DATA SWI (B] IN4001 B DATA SW2 Figure 3.1 Procedure : 1. Wire the circuit shown in Figure 3.1. The inputs A and B come from DATA SWITCHES SW1 and SW2. You will measure the output voltage C with respect to ground. 2. Using SW1 and SW2, apply the input voltages indicated in Table I to the logic gate. For each set of inputs, monitor the output voltage and record in Table I. 3. Using positive logic assignments, convert the voltage levels in Table I into binary 1's and 0's and transfer to Table II Table I Table |I Table III A C A OV OV OV +5V +5V OV +5V +5V 4. Study Table Il and determine the logic function being performed. Logic Function Convert the voltage levels in Table I into 1's and 0's using negative logic assignment and transfer to Table III. NEGATIVE LOGIC is that the logic is zero (0) if voltage is above 3 volts and logic one (1) if the voltage is below 2 volts. 5. Study Table IIlI and determine the logic function being performed. Logic Function 平

Material Needed: 2- IN4001 Silicon Diodes 1- 1K resistor 1 - 10K resistor 1k Ohm (A) IN4001 ELECTRONIC WORKBENCH OUTP DATA SWI (B] IN4001 B DATA SW2 Figure 3.1 Procedure : 1. Wire the circuit shown in Figure 3.1. The inputs A and B come from DATA SWITCHES SW1 and SW2. You will measure the output voltage C with respect to ground. 2. Using SW1 and SW2, apply the input voltages indicated in Table I to the logic gate. For each set of inputs, monitor the output voltage and record in Table I. 3. Using positive logic assignments, convert the voltage levels in Table I into binary 1's and 0's and transfer to Table II Table I Table |I Table III A C A OV OV OV +5V +5V OV +5V +5V 4. Study Table Il and determine the logic function being performed. Logic Function Convert the voltage levels in Table I into 1's and 0's using negative logic assignment and transfer to Table III. NEGATIVE LOGIC is that the logic is zero (0) if voltage is above 3 volts and logic one (1) if the voltage is below 2 volts. 5. Study Table IIlI and determine the logic function being performed. Logic Function 平

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

D-MOSFET: lVtl= 2 V, Idss =10 mA, Is=1.6 mA, rd=14 K, RL=2 K. Calculate the dc drain-to-source voltage. Please write your answer as a V and don’t use units in the answer. Please use one digit after the dot.
Project 3: - Design MCU based system to form the following state machine? Proj4:- redesign the project using active low method (method 2) for LEDs? Show all design parts (the circuit and the program) and the state machine diagram.
Good day. This is Fundamentals of Electronics Circuits subject. Please do help. No need for solutions
How are branch circuits rated? See PEC 2.10.3
Derive the gain of ?i /?o for the circuit of figure 3
3. Given: VS1: 18 voltsVS2: -1 voltsRB1: 1000 ohmsRB2: 6500 ohmsRB3: 8000 ohmsRB4: 5000 ohmsB=beta: 75RE: 540 ohmsVE: ? volts
S3) Calculate the current IB, IC and voltage VCE in the circuit in the figure and examine whether it is conduction or not? (VBE=0,7V , β=80)
Step-by-step with explanation. B) The interface shown can be used for low-current LEDs. Assume the LED voltage drop is 2.5 V. The resistor is 5Kohm. When the software outputs a high, the voltage on PPO becomes 4.89 V. When the software outputs a low, the voltage on PPO becomes 0.4 V. What is the LED current when the LED is on? (Vdd=+5V)
Problem 1. We have identical crystalline silicon solar cells available, with a short circuit current of 4 A and an open circuitvoltage of 0.6 V at STC. These cells are used to make a PV module with 54 cells connected in series. I. What is the open circuit voltage of the module at STC? Assume that the interconnection losses arenegligible.II. What is the short circuit current of the module at STC? III. Assume that the module does not have any bypass diodes. If the module is partially shaded and one ofthe cells is only able to produce 2 A, what will be the new short circuit current under these conditions?
. a) Calculate and plot the current flowing through the pn junctions of device #2 on your 3311 wafer as a function of voltage over the range of -3 volts to plus 1.5 (or so) volts on a linear scale. b) plot the I-V curve for the forward voltage on a log scale. c) What voltages correspond to 10 A/cm2, 100 A/cm2, 1000 A/cm2, 10,000 A/cm2 and 100,000 A/cm2? d) What is the current and current density when the applied voltage is equal to the built-in voltage? e) what are your thoughts on applying a voltage greater than the built-in voltage to a pn junction diode?
Maximum dc source current is defined by NEC 690.8(A) as the sum of parallel module rated short circuit currents multiplied by? A.110% B. 125% C. 150% D. 200%
Given a voltage divider configuration of a D-MOSFET with IDSS = 12mA, VP = -3V, yos = 35µS, R1 = 91MΩ, RD = 6.8kΩ, RS = 3.3kΩ, VDD = 18V(i) Draw a complete circuit as describe above.(ii) Determine the operating point, IDQ and VGSQ using mathematical approach.(iii) Determine the operating point, IDQ and VGSQ using graphical approach.(iv) Voltage across drain and source terminals, VDS .