Number 5  I put A and it was

Q: pordinate direction angles of the

A: finding the co-ordinate of points A0,0,6, B2,-3,0 And C 3,2,0 and( 2) calculating the position…

Q: Answer a) and b) only

A:

Q: show FBD

A: As per question asked below is the FBD of the given problem

Q: Please help me with number 9,10 and 16. This is not graded.

A: 9. Length of threads=16.5 10. No. Of threads=20/2.5= 8 16. No. Of threads=20/1.5=13

Q: following figure. TH and a nin at D The

A: Force in member AB is required

Q: find Ax, Ay and Az

A: Write the given data with suitable variables. W=558 N/ma=1.5 mb=3 mc=1 m

Q: mum weight of cylinder th your answer in two decimal

A: given:

Q: 기e hat,

A: Solution:-          given,                   τxy=τyx                   τyz=τxz   Prove that,…

Q: wo

A:

Q: from the fu

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: the centre distance in mm

A: Given data;  Compound gear train with gears;  p=20 teeth  Q= 40 teeth  R= 15 teeth  S=20 TeethGears…

Q: what would be the weight of the block

A:

Q: Given b- Bm * 3m a 60 degrees R6m C 10 m Eind

A: Solution:Given,b=8mr=3m @ 60 degreesR=6mC=10m Scale(1m=1cm)

Q: What will be the largest weight of the

A: Given: Moment about OA is 315 Nm To determine W

Q: Iflow rat

A:

Q: m

A:

Q: ths angle of the three forse acting on hook

A: given: determine the resultant and the angle of the three forces acting on hook?

Q: Shift weight A so the lever would balance at 7/8 of the total length of the board measured from left…

A:

Q: 3) and B.d

A:

Q: Number 7  I put C and it was incorrect

A: As per technician A: A says that the strut has internal defects and strut replacement is necessary.…

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: value of h will be

A: Given: Figure shows a schematic diagram of simple watt governor mechanismwith spindle o1o2 rotating…

Q: D raio s.f.D and B.M.

A:

Q: 4. WHAT IS THE VOLUME OF THE PART?

A: Given:- Unit:- MMGS Material:- Copper To find:- 1) Volume 2) Mass 3) Center of mass

Q: 5. What will be the accuracy of

A: Need to find accuracy .

Q: in 5 minutes please Diameter=38 L

A:

Q: angle angle and 3 1 ween two bearin

A:

Q: Please, it´s urgent.

A: Given Load = 30 N = 6.74 lb Density = 7850 kg/m3 = 0.283lb/pulg3 Thickness = 13mm = 0.511811 pulg To…

Q: in figure, the length of wire

A: GIVEN:

Q: Solve question 8 please

A: Solution to Q8 as mentioned by the student:

Q: find the diameter

A: Given : Dimension of a cylindrical side riser   Height= Diameter 25cm×15cm×5 cm steel casting from…

Q: Can you please do 5.67.   Thx

A: Draw the free body diagram.

Q: inclined plane, on the plate to mak

A:

Q: D and e please

A:

Q: number d and e?

A: To solve this question, we will use the moment equilibrium equation which is mentioned in the…

Q: y 1 in. 3 in. -3 in.-

A: Area of the triangle, A1=1/2(3)6=9in2 Area of the square, A2=3(3)=9 in2 Area of the quarter circle,…

Q: In step 4, it should be the A and not the y right? So it should be FBD divided by 4.04 which is the…

A:

Q: 10 (2) Find the O

A: Given

Q: 18m -0 -188m

A:

Q: Determine the name of the device and

A: Given; Moist air at 350 CRelative humidity is entering a psychometric deviceand leaving at,…

Q: Find I and Ø

A: we have to find the shar and twist in each section

Q: This is a Flange. What does The number 3 Represent

A:

Q: v what is the distance

A: To find the distance.

Q: What will be the distance

A: Given; A leaf is caught in a whirlpool.Leaf distance=120mThe whirlpool can be described by the…

Q: The part denoted by number 1 is the

A: According to the diagram provided in the question. It is cooling system of an automobile engine. The…

Q: the regritade ef the

A:

Q: Draw the isomtre

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: fy its location a

A: The uniformly applied load (w)= x2+3x+C. The force acting on point A (F)=200 N/m. The distance…

Q: stur

A: given:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.