Which of the following startements is incomeef? A Under and fatigne 1oading materials may fail at creep Stress well beow the Young's modulus of the matenial B- During Steadt-state creep there is a balance between whmpeting processes of strain-hardening and recovery. C TO reduce dislocation creep second phase precipitates can be infroduced to the material. high meting a material with temperature Can Choosing offset creep. D- E - A A visco elastic matenial Shows a ombinafion of elastic response and a viscous fion-

Which of the following startements is incomeef? A Under and fatigne 1oading materials may fail at creep Stress well beow the Young's modulus of the matenial B- During Steadt-state creep there is a balance between whmpeting processes of strain-hardening and recovery. C TO reduce dislocation creep second phase precipitates can be infroduced to the material. high meting a material with temperature Can Choosing offset creep. D- E - A A visco elastic matenial Shows a ombinafion of elastic response and a viscous fion-

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.5P

See similar textbooks

Similar questions

If there is to be extensive replacement in a substitutional solid solutions"SSS", the atoms must be nearly the same size. Select one: O True O False The load-deformation depends on the rate of loading in viscoelastic Materials.
A single crystal of BCC iron is subjected to tensile stress of 100 MPa along the [001] direction. Which of the two slip systems ((211) –[ 111 ] or (321)–[ 111 ]) is going to yield first?
Pearlite structure contains the alternating layers of austenite and bainite. A) Doğru B Yanlış
Normal stress of alumi
The apparent viscosity of- ----- decreased with increasing shear stress. Thixotropic O Rheopectic O Pseudoplastic O Dilatant O Bingham plastic O
Q7> Ductile-to-brittle transition temperature (DBTT) is a very important parameter in the design of metallic materials for engineering applications. It has been well known that most of BCC and HCP metals show the DBT phenomenon; however, there is no DBTT in FCC metals. (a) Explain the reason in terms of deformation and fracture. You must compare the BCC and FCC. (b) The ductile fracture surface consists of many dimples. Explain their formation mechanism from the concept of point defects. (c) There are two types in the brittle fracture. Explain and Compare them.
What is the relationship between the silica structure and the Bowen's reaction discontinuous series?
If the extruder can withstand a pressure of no more than 15MN/m2, what is the maximum shear stress the polymer can be submitted to at the metering section of the screw? The screw has a channel depth of 5mm and the polyamide being used has a melt viscosity of 42Ns/m2.
A chemicals company is looking to optimise the materials selection for their synthesis vessel with safety being the key priority. The tank can be treated as a small thin-walled spherical pressure vessel and the engineers are considering a 'yield before break' design concept. Given that a crack of length will propagate by fast fracture when the stress intensity factor reaches the fracture toughness of the material select the correct materials property index relevant to this design criterion. Fracture toughness K₁=Yo√na IC OM= OM= OM= KIC of OM= d OM= P K 2 IC K IC P o a M= K IC K 2 IC
14) Inc a) Copper and its alloys do not fail due to cycling loading if the applied stress amplitude is below a certain level. b) Alloys with HCP crystal structure do not fail due to cycling loading if the applied stress amplitude is below a certain level. c) If there exist many slip systems such metals and alloys do not fail due to cycling loading if the applied stress amplitude is below a certain level. d) The practical rule that says there exist a fatigue limit for iron based alloys is not strictly true. 15) Indicate the incorrect expression: a) Better surface finish would help increase fatigue life. b) All kinds of inhomogenity would be detrimental in number of cycles that material can terms of the endure regardless of the stress level. c) Corrosion on a material that has excellent surface finish would not affect fatigue behavior of that part. d) Sand blasting as a source of compressive stresses would be useful under fatigue conditions
The assembly consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 86 GPa, α= 18 × 10−6/°C] has an outside diameter of 33 mm and an inside diameter of 27 mm. The ceramic core [E = 320 GPa, α= 2.5 × 10−6/°C] has a diameter of 27 mm. At a temperature of 15°C, the assembly is unstressed. Assume L = 320 mm. Determine the largest temperature increase Δ⁢t that is acceptable for the assembly if the normal stress in the longitudinal direction of the brass shell must not exceed 65 MPa.
cmplete solution