Step by step solution please Consider the schematic of a riveted lap jointsubjected to tensile load F, as shown below. Let d be thediameter of the rivets, and S, be the maximumpermissible tensile stress in the plates. What should bethe minimum value for the thickness of the plates toguard against tensile failure of the plates? Assume theplates to be identical.

Given; What should be the minimum value for the thickness of the plates to guard against tensile…

Answered: minimum value for the thickness of the…

Engineering

Mechanical Engineering

minimum value for the thickness of the plates

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Related questions

Q: A steady flow compressor handles 113.3 m3/min of nitrogen measured at intake where p1 = 97.22 kPa…

Q: What general trend did you observe from set-ups 1 to 2? Support your answer by using the data…

A: From setup 1 to 3, we observe that the initial velocity of the Marble A was varied. Ignoring all the…

Q: Water inter a condenser at a mass flow rate of (2.5 kg/s) and (21 kPa and 65 C), and exit with (h=…

Q: Question: Consider the following thermal system. The input is T in, and the output is the…

A: Given : To find : State space model

Q: 058 Btu/h · ft · °R). The inner temperature of the insulation is 67°F. The outer temperature of the…

Q: A centrifugal pump is shown in the figure below. Absolute velocity, V₂ b₂ = 1.0 cm 0₂= 45% w, T…

Q: Vo = 0.8 m/s as it passes position A. Neglect th mass of the pulleys and cable and determine th…

A: Solution : Given data :- v0 =0.8 m/s

Q: A 50-mm diameter solid shaft, with a length of 1 meter, is supported at one end and free in the…

Q: The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined…

A: Given DataW=250NP=100NV=17.862 m/s {As velocity is not given in question we have to take the…

Q: Locate the centroid of the shaded area. Thanks in advance

Q: 1. At time t=0, the velocity of cylinder A is 0.3 m/s down. By the methods of this article,…

Q: 1-74. Member B is subjected to a compressive force of 3 kN. If A and B are both made of wood and are…

Q: R₁ -2m- B -2m- 30 kN/m -5m- C D R₂

A: Draw the shear force and bending moment diagram and find its maximum values in the beam.

Q: If a certain gas has Cp of 1.005 kJ/kg-K and Cv of 0.678 kJ/kg-K, determine the value of k, T2,…

A: Given data cP =1.005 kJ/kgKcV = 0.678 kJ/kgKP1 = 101.325 kPaT1 = 77°C1-2 : Adiabatic Compression…

Q: Using the psychrometric chart, for atmospheric air at 1 atm. Dry-bulb Temperature = 23 degrees C…

A: Given Dry bulb temperature, DBT = 23oC Relative humidity RH = 50 % Find Wet bulb temperature,…

Q: The 35-kg roll of paper rests along the wall where the coefficient of kinetic friction is μ = 0.2. A…

Q: Question 8 Let z = g(x, y) = x³ + xy³ + y² - 6x - 2y + 4, where x = r cos (0) and y = r sin(0). Use…

A: Find the value of dz/dthetha.

Q: The gear A on the drive shaft of the outboard motor has a radius TA = 0.7 in. and the meshed pinion…

A: Angular velocity of propeller in t= 1.7 sec.

Q: 2-66. Determine the placement d of the pin on the 1-m-diameter circular gate so that it is on the…

A: According to the details provided in the question, we need to calculate the resultant force on the…

Q: of the smooth vertical slot. If the block starts from rest when The block has a ma kg and moves the…

A: Solution:- Given data :- k =100 N/mvB =2.5 m/ssB =0.15 m

Q: Find the stresses at point C. -1.5 m 250 mm 125 mm 50 mm 4 m 1.5 m 2 m 2.5 m 50 kN/m

A: Find the stresses at point C.

Q: A centrifugal pump is used to supply a highly viscous fluid to a chemical plant. The chemical plant…

A: Given data Chemical Plant is located at a height of 20 m above the pumping level.The flow rate in…

Q: Q2. An object moves from rest in a straight path with acceleration 2 m/s² until it travels a…

Q: The pressures at the beginning and end of compression in an Otto cycle engine are 1 kg/cm² and 6…

A: Given Initial pressure, P1 = 1 kg/cm2 Final pressure, P2 = 6 kg/cm2 Find Air standard efficiency

Q: Sketch a plot that contains a lateral strain for a material undergoing a temperature change which…

Q: Determine the mole fractions of a gas mixture that consists of 75% CH4 and 25% CO₂ by mass. Also…

A: Given: mixture : 75% CH4 & 25% CO2

Q: Rocket is presented with 20 Harbulary Batteries, 10 of which are real and 10 of which are fake. He…

A: Given : n = 20 To find : Calculate the appropriate values to indicate Rocket’s sensitivity and…

Q: rods as shown in the figure below. Rod A has a diameter of 12 mm and manufactured from steel with…

Q: a- When the temperature increases, the Viscosity (u) of the liquid b- Water Turbines can be…

A: As per the guidelines of company we are subjected to solve only first three parts of a question…

Q: 2. The angular acceleration of the disk is defined by a= 3t² + 12 rad/s, where t is inn seconds. If…

A: Given Data The angular acceleration of the disk is:α=3t2+12 rad/s The angular velocity of the disk…

Q: A closed system containing 1 kg of air at 10 bar and 227°C expand adiabatically to pressure of 1…

A: A closed system containing 1 kilogramme of air, 10 bar, and 227oC expands adiabatically to a…

Q: Exhaust gasses from a diesel engine are used to heat water in an insulated heat exchanger. Refer to…

Q: The structure at dimensions of 10^-9m is called structure

Q: Find the entropy production and determine if the cycle operates irreverisbly, reverisbly, or…

Q: These are essential in a design process Assumptions Product specification Market need Iterative

A: 1) Federal law applies to everyone in country but state and local laws applies to people of that…

Q: R13-6. The bottle rests at a distance of 3 ft from the center of the horizontal platform. If the…

Q: 43. The exposure at 25 cm from a radioactive source is 16 mR/h. At what distance will the exposure…

A: Initial exposure rate =I1=16mR/h at D1=25cmNow,New Exposure rate=64mR/h=I2Let new distance =D2We…

Q: A steel column of hollow circular cross section shown in Figure is supported on a circular steel…

Q: Part A The 200-lb wheel has a radius of gyration of kg = 0.75 ft. The upper wire is subjected to a…

Q: Consider a coupled system with two blocks, A of mass m and B of mass 2m coupled by springs of spring…

A: Given : To find: Mode

Q: In the ideal Rankine cycle shown, the boiler pressure is 6 MPa and the condenser pressure is 8 kPa.…

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

Q: . Helium gas expands from 20 psia, 600ºR and 9 ft³ to 15 psia in a polytropic process with n =…

Q: To investigate the effect of force orientation on the velocity of a collar, following experiment has…

Q: question in my homework related chemical material lesson. The following below is my question. Please…

A: Basically,four major mechanisms or stages for strengthening of metal in material science and…

Q: The beam is subjected to the uniform distributed load shown. Draw the shear and moment diagrams for…

A: For the given beam, the point in section AB where shear force changes sign (x2 metres from A) is to…

Q: A small turbine runs an aircraft refrigeration system. Air enters the turbine, at 4 bar and 40°C…

A: In this case, we know that an aircraft refrigeration system is powered by a tiny turbine.At 4 bar…

Q: If FA=8 kN and FB = 5 kN, find the resultant force, find the components of the moment about point o,…

A: Solution: Given data: FA = 8 KN ,FB =5 kN

Q: A car travels at 40 m/s, decelerates at a constant 4 m/s2 until rest. Determine speed and distance…

Q: A motor is driving a solid circular steel shaft transmits 40kW of power at 500 rpm. If the diameter…

Concept explainers

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.

Question

Step by step solution please

Consider the schematic of a riveted lap joint
subjected to tensile load F, as shown below. Let d be the
diameter of the rivets, and S, be the maximum
permissible tensile stress in the plates. What should be
the minimum value for the thickness of the plates to
guard against tensile failure of the plates? Assume the
plates to be identical.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axialtensile load of 40 kN. What will be the stress in the bar? What further increase in loadis possible if the stress in the bar is limited to 225 MN/m2?
A cylinder head of a steam engine is held on by 14bolts. The effective diameter of the cylinder is 35cm and the steam pressure is 85N/mm².Assuming that the bolts are not initially stressed; find the size of bolts if the tensile stress is not to exceed 20N/mm²
A spherical pressure vessel 300 mm in diameter has a uniform thickness of 6 mm. The vessel contain gas under pressure of 6000 kPa. If the ultimate tensile stress is 450 MPa, what is the factor safety with respect to tensile failure?
-Determine the safe tensile load for bolts of M20 and M42 . Assume that the bolts are not initially stressed and take the safe tensile stręss as 2000 kg/cm" . 2- An eye bolt carries a tensile load of 2000 kg. Find the size of the bolt, if the tensile stress is not to exceed 1000 kg/cm. Also draw a neat proportioned figure for the bolt or
In buckling experiment a steel column (E=210 Gpa) was examined in pin-fixed method. It endured a load up to 1190 N. Its length is 600 mm cross sectional width is 20 mm, thickness is 4 mm. Find the critical stress and compare it with the actual stress (error%).
A spherical pressure vessel 400-mm in diameter has a uniform thickness of 6 mm. The vessel contain gas under a pressure of 8,000 KPa. If the ultimate tensile stress of the material is 420 MPa, what is the factor of safety with respect to tensile failure?
A bar of length 5 m is subjected to an axial tensile out of 100 KN The bar is 25 min diameter for 2 mof its length 30 mm diameter for I mor its length, and 20 mm diameter for the remaining 2 m of its length, Taking E= 2 x 10' Calculate the total increase in length of the bur.
(a)Describe, with a labelled diagram, how you would measure accurately theextension of such a wire under an applied load. (b) The graph below shows how the extension of a wire varies with the loadapplied to it. The wire used has a length of 3m and a diameter of 5 x 10^-4m i. Calculate the tensile stress produced by a load of 50N.ii. Find the energy stored in the wire when the load is acting.iii. Calculate the reduction in gravitational PE of a 5kg mass used to providethe load.iv. Calculate Young's modulus for the metal of the wire.
A bar is applied a tensile load of 50 kN having diameter 10 mm, Calculate the tensile stress induced in the bar.
Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane as shown in Fig.1 Initially, all the rods are adjusted to share the load equally. Neglecting any chance of buckling, and taking Esteel= 205 GPa and Ecopper 100 GPa, determine the initial and final stresses when a further load of 20 kN is added.
A cylinder head of a steam engine is held on by 14 bolts. The effective diameter of the cylinder is 35 cm and the steam pressure is 8.5 kg/cm2. Assuming that the bolts are not initially stressed, find the diameter of each of the bolts if the tensile stress is not to exceed 200 kg/cm2.
A copper rod of 50mm diameter is surrounded by a steel tube of 100mm external diameter, the ends being firmly fastened together, subjected to a compressive load of 30kN. Youngs modulus of elasticity of steel is 200GPa and that of copper is 120GPa. Evaluate the stress produced in the copper rod and steel tube.