Explain properly and also show the plotted variation, last answer was not showing anything at all mm².A cylindrical shell with an internal diameter of 160 mm and a wallthickness of 45 mm is subjected to an internal pressure of 52.5Find the maximum and minimum intensities of the hoop stressacross the section. Plot the variation of the hoop stress across thesection.

hoop stressExplanation:Step 1:Step 2: Step 3: Step 4:

Answered: mm². A cylindrical shell with an…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the principal stresses andmaximum in-plane shear stress of given stresselement.
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar.
The 2-in.-diameter drive shaft AB on the helicopter is subjected to an axial tension of 10 000 lb and a torque of 300 lb # ft. Determine the principal stresses and the maximum in-plane shear stress that act at a point on thethe surface of the shaft.
Determine the normal and shear stresses at point Aand B. The cross-section of the bar is 12x12 mm.
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 556 mm2 and P= 36.79 kN. Round off the final answer to four decimal places.
The hollow circular shaft is subjected to the torque of 4 kN # m. Determine the principal stresses at a point on the surface of the shaft.
Using transformation equations of plane stress, determine the normal and shear stress components for X’-axis located 0.5 radians clockwise from x-axis. The non-zero stress components are given as follows, σx= 200 MPa, σy= 100 MPa, τxy= -50 MPa.
Determine the torsional stress in the thin-walled tube as shown:
Determine the maximum shear stress for the above stress state (ksi)
Determine the principal planes and the principal stresses for the state of plane stress resulting from the superposition of the two states of stress shown. Given: X = 60 MPa and Y = 20 MPa. Determine the orientation of the principal plane in the first and second quadrant. Determine the maximum/minimum principal stresses
The stress of member AB is equal to the stress of member BC having a diameter of 100 mm. Determine the diameter of member AB.
The 6-hp reducer motor can turn at 1200 rev>min. If the allowable shear stress for the shaft is tallow = 6 ksi, determine the smallest diameter of the shaft to the nearest 1 16 in. that can be used.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

mm². A cylindrical shell with an internal diameter of 160 mm and a wall thickness of 45 mm is subjected to an internal pressure of 52.5 Find the maximum and minimum intensities of the hoop stress across the section. Plot the variation of the hoop stress across the section.