SN=14A compound shaft is made bymounting a brass sleeve on a steelshaft (which is considered as parallelconnection). The shaft is subjectedto a torque T at point B in such a waythat the torque on the sleeve is twicethat on the shaft. Determine the ratioof external diameter of the sleeve tothat of the shaft. What will be thetorque transmitted by the compoundshaft if the steel shaft diameter is 56mm and the limiting values of theshear stresses in the brass and thesteel are 50 MPa and 85 MParespectively? Gsteel= 2.4 Gbrass.SN=Student Number...60+SN60+SNYour answerIT

Answered: Image /qna-images/answer/a89991a9-f784-4106-88c4-2a9a7c3060be.jpg

mpound shaft is made by ting a brass sleeve on a steel (which is considered as parallel ection). The shaft is subjected prque T at point B in such a way he torque on the sleeve is twice on the shaft. Determine the ratio ernal diameter of the sleeve to of the shaft. What will be the o trancmitted by the mnound

mpound shaft is made by ting a brass sleeve on a steel (which is considered as parallel ection). The shaft is subjected prque T at point B in such a way he torque on the sleeve is twice on the shaft. Determine the ratio ernal diameter of the sleeve to of the shaft. What will be the o trancmitted by the mnound

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Similar questions

A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A propeller shaft for a small yacht is made ofa solid steel bar 104 mm in diameter. The allowablestress in shear is 48 MPa, and the allowable rate oftwist is 2.08 in 3.5 meters.(a) Assuming that the shear modulus of elasticityis G = 80 GPa, determine the maximum torqueTmax that can be applied to the shaft.(b) Repeat part (a) if the shaft is now hollow withan inner diameter of 5d/8. Compare Tmax valuesto corresponding values from part (a).
Q.12A solid shaft of diameter 'd' and length " issubjected to torque T. Another shaft B ofsome length, material but twice the diameter is subjected to the torque 2T. The ratio of the angle of twist of shaft A to shaft B is-
a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of torque 20% take maximum shear alloy stress as 55mpa
A hollow shaft transmits 9 MW at 300 rev/min. It is supposed that the maximum allowable stress is not to exceed 70 MN/m2 nor the angle of twist 0.5 degree per metre length of shafting. If the outside diameter of the shaft is 400 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m2. *
The compound shaft, consisting of steel and aluminium segments, carries the two torques shown in the figure. Determine the maximum permissible value of T subject to the following design conditions: F.S. = 1.5, Tult steel = 95 MPa, Tult aluminium = 70 MPa, and o < 6° (9 is the angle of rotation of the free end). Use G = 83 GPa for steel and G = 28 GPa for aluminium
A hollow shaft has to transmit 6MW at 150rev / min. The maximum allowable stress is not to exceed 60 MN / m? nor the angle of twist 0.3 ° per meter length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN / m?
A solid shaft 100 mm diameter transmits 100.6 horsepower with a maximum allowable shear stress 25 MN/m ^2 . What is the spced of rotation of the shaft in (r.p.m)? (b) If the solid shaft is replaced by the hollow shafl transmitting 100 kW at the same rotation speed of the solid shaft. The hollow shaft has a mean torque =5/6 of maximum torque with the angle of twist 0.35° per meter length of the shafl and G= 80 GN/m^2 Determine the dimensions ofr the hollow shaft if the internal diameter of the shaft is to be 80 % of the external diameter.
Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.
A hollow shaft has to transmit 6 MW at 150 rev/min. The maximum allowable stress is not to exceed 60 MN/m² nor the angle of twist 0.3 per metre length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m².
A hollow shaft for a rotary compressor is to be designed to transmit a maximum of torque of 4750 N-m. The shear stress in shaft, if the ratio of the inside to the outside diameter is 0.4
SS 304 steel shaft is 3 m long and has an outer diameter of60 mm. When it is rotating at 60 rad/s, it transmits 30 kWof power from the engine to the generator. Determine thefollowing: a. The smallest thickness of the shaft if the allowableshear stress is 150 MPa and the shaft is restricted notto twist more than 0.08 rad. Use G for steel = 83 GPa. b. The percentage savings in weight had the generatorutilized a solid shaft. Assume same material, length andtorque capacity.