multi story structure is to be constructed using concrete that has a unit weight of 150 pcf. The proposed construction is to be a 6 story building using 1 set of shores and 2 levels of reshores. The building is to be 75 feet by 100 feet and the floor heights are to be 15 feet between each 9 inch floor slab. Calculate the loads in all shores and reshores when the final floor is to be poured

multi story structure is to be constructed using concrete that has a unit weight of 150 pcf. The proposed construction is to be a 6 story building using 1 set of shores and 2 levels of reshores. The building is to be 75 feet by 100 feet and the floor heights are to be 15 feet between each 9 inch floor slab. Calculate the loads in all shores and reshores when the final floor is to be poured

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter29: Design Criteria For Structural Loading

Section: Chapter Questions

Problem 29.1Q

See similar textbooks

Similar questions

Determine the maximum combined loads using the recommendedAISC expressions for LRFD. D = 25 psf, Lr = 20 psf and W = ;26 psf
Determine the maximum combined loads using the recommendedAISC expressions for LRFD. D = 9000 lb, L = 5000 lb, Lr = 2500 lb, E = ;6500 lb (Ans. 20,050 lb)
Determine the maximum combined loads using the recommendedAISC expressions for LRFD. D = 100 psf, L = 70 psf, R = 12 psf, Lr = 20 psf and S = 30 psf
Given: ▪ Proposed Eight-storey with roof deck commercial mix use building▪ 20 x 32 m with first floor being 3.5 meter in height and rest at 3.2 meter with 1.0-meter parapet ▪ 5 bays x 7 bays (5@ 4-meter x 8@ 4 meter typical) ▪ Assume a 10 kPa regular weight of the typical floor area except at roof deck being 8 kPa. Occupancy Category IIIEnclosedWind speed, V= 260kphExposure C Calculate the required wind pressure on the walls and parapet applying the code provision under Directional Procedure for Buildings of All Heights (NSCP section 207B) **ALL UNITS MUST BE IN KILOPASCAL (kpa)photos for reference
Please show detailed solution: The office building has interior columns spaced 5 m apart in perpendicular directions. Determine the reduced live load supported by a typical interior column located on the first floor under the offices. Consider flat roof loading equivalent to 1.1 KPa. ANSWER: 197.18KPA
The second floor of a light manufacturing building is constructed from a 5-in.-thick stone concrete slab with an added 4-in. cinder concrete fill as shown. If the suspended ceiling of the first floor consists of metal lath and gypsum plaster, determine the dead load for design in pounds per square foot of floor area.
What is the difference between the dead load and the live load of a building?
A building design has spiral reinforced concrete column 9m high with a general cross sectional diameter of 45inches. Determine the required materials by the volume method and the linear meter method using class A concrete if there are 6 columns in the plan.
. A seven-story steel-frame office building will have columns spaced 7 m on centerand will have typical interior and exterior finishes. Compute the allowable total anddifferential settlements for this building
Wind can produce very high drag loads on high-rise bulidings. Since calculating the áow around a buildingis quite diffcult, you decide to perform an experiment to find the drag on the nearly completed Mirabellabuilding at Univesity Drive and Myrtle Avenue in Tempe. The building is 250 ft tall and approximately 210ft wide (at its widest part) A) determine the drag on the Mirabella building for a sustained wind speed of 40 mph. Supposethat the temperature remains the same both inside and outside of the wind tunnel test section. If theatmospheric pressure is 100 kPa, what would the pressure have to be inside the tunnel test section tomaintain dynamic similarity between the model and the full-scale building? (You may assume that thetunnel is operating at maximum speed.
compute the maximum combined loads using the recommended ASD expressions from the AISC
A seven-story steel-frame office building will have columns spaced 7 m on-center and will havetypical interior and exterior finishes. Determine the allowable total and differential settlementsfor this building.