n ammeter model consists of an ideal ammeter in series with a 20-22 resistor. It is connected with a current source and an unknown esistor Rx as shown in the given figure. The ammeter reading is noted. When a potentiometer R is added and adjusted until the mmeter reading drops to one half its previous reading, then R = 67 2. What is the value of Rx? he value of Rx is 20 92 S2. Ammeter model

n ammeter model consists of an ideal ammeter in series with a 20-22 resistor. It is connected with a current source and an unknown esistor Rx as shown in the given figure. The ammeter reading is noted. When a potentiometer R is added and adjusted until the mmeter reading drops to one half its previous reading, then R = 67 2. What is the value of Rx? he value of Rx is 20 92 S2. Ammeter model

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 1PA: An AC electric motor is connected to a 240-V, 60-Hz source. A clamp-on ammeter with a peak hold...

See similar textbooks

Similar questions

An AC electric motor is connected to a 240-V, 60-Hz source. A clamp-on ammeter with a peak hold function reveals that the motor has an inrush current of 34 A when the motor is first started. Your job is to reduce the inrush current to a value of 20 A by connecting a resistor in series with the motor. The resistor will be shunted out of the circuit after the motor is started. Using an ohmmeter, you find that the motor has a wire resistance of 3 . How much resistance should be connected in series with the motor to reduce the starting current to 20 A?
Suppose that the voltage source has an internal series resistance of 50 Ω. How would the outputvoltage be affected (assuming that R1 and R2 are the same as you specified earlier)? Work out your resultsfor both the ideal voltage source and for the voltage source with the internal impedance. R1 and R2 are both 3 Ohms and Vin = 10 V
An Engineer is tasked with implementing a lighting circuit with a 24 V battery. Part of the task included making sure power was conserved, e.g., ensuring the light stays off during daytime. The engineer selects a generic phototransistor to detect enough ambient light when present. The circuit below contains two transistors in series Q1, & Q2. This means that for the 35-Watt lamp (load) to work both transistors must be “ON” (or conducting), else the lamp is “OFF” (no current flows). Transistor Q1 is turned on by actuating the switch “SW1”. Transistor Q2 is turned on by the phototransistor Q4. The circuit is powered by a 24V Battery. Figure 1 shows the control circuit schematic and the simplified (equivalent) logic gate version of the circuit. (Hint: calculate your answer using Ohms law.)
Hey please reply as soon as posible Using only source transformation and without eliminating ix, reduce the circuit in Figure to a single voltage source and a single resistor, then obtain ix using Ohm's law. A) What is the value of the source voltage in V and what is the value of the resistor in Ω? B) What is the value of ix in Amps?
Shown below is a typical setup for a solar battery system. Sun’s energy is converted to electricity using solar PV modules. To match the output voltage of the PV module to the battery's, a charge controller is used which is a DC-DC converter. The sun’s output power is given as 1000 W/m2. The solar module has a surface area of 1 m^2 with a conversion efficiency of 10%. A charge controller converts the 20V module voltage to 12V battery voltage, with an efficiency of 84% The battery is 12V with a capacity of 10Ah. Assuming the battery is half empty (or half full, depending on your personality) and the bulb is powered on, how long will it take for the battery to be fully charged? How long can the bulb be powered at night, assuming full battery when the sun goes down and that you can fully drain the battery? (answer in hours)
In the Zener circuit shown below, calculate the Zener current IZ when VZ=10 V, E=14 V, R1=298 ohm, and R2 =298 ohm.
Using only source transformation and without eliminating ix, reduce the circuit in Figure to a single voltage source and a single resistor, then obtain ix using Ohm's law. A) What is the value of the source voltage in V and what is the value of the resistor in Ω? B) What is the value of ix in Amps?
In the circuit above, the ammeter (A) is an ideal ammeter (so without internal resistance); the voltmeter (V) is also ideal (so with an infinitely large resistance). The two e.m.f. sources have negligible internal resistance. The voltmeter reads a positive value when the voltage of the ++-connector is higher than the voltage of the -−-connector (see picture) The ammeter reads a positive value when the current runs from the ++-connector to the -−-connector. What are the readings of the ammeter and the voltmeter?
Consider a simple circuit with an EMF ε=25V and two resistors R1 = 50Ω and R2 = 10Ω. Now consider two configurations of this circuit, Case 1 where the resistors are in a series configuration, and Case 2 where the resistors are in a parallel configuration. Using Ohm’s Law and Kirchoff’s Laws, determine the total current and total resistance in the circuit in each case. Are the total resistances different or the same for the two cases? Give an explanation of how you combined the separate resistances in each of these cases. Show your mathematical work and sketch or attach an image of any circuits you build in the simulation or by hand.
For the circuit shown in Figure3, given that R C = 3 KΩ, R L=1KΩ, V CC = 15 V, voltagegain Av=10 and IB = 10mA. The circuit have input signal vin of =2v. Determine the valueof IC please explain the solution
Using only source transformation and without eliminating ix, reduce the circuit in Figure to a single voltage source and a single resistor, then obtain ix using Ohm's law. Please answer the 2 questions A) What is the value of the source voltage in V and what is the value of the resistor in Ω? B) What is the value of ix in Amps?
Activity 3:Consider the circuits below with the following nominal values:Vz = 6.8 VIz(min) = 1 mAInput voltage = 10 ± 1 volts. Maximum load current is 150 mAMinimum load current is 10 mA(3-a) Describe the operation of Circuit A. What is the function accomplished?(3-b) Determine the value of R to always maintain the Zener turned on (Circuit A).(3-c) Evaluate the maximum current and maximum power of the Zener (Circuit A).(3-d) Use Multisim to verify all of your results (assume Rload of 750 Ω)(3-e) Analyze Circuit B assuming the same parameters and components used in Circuit A.Describe the operation of the circuit clearly, and use Multisim to support your arguments.