n the packaging industry, assume that a strain gauge sensor is used to measure the weight of a food package. The strain gauge changes its output DC voltage value whenever some force/weight is applied on it. The food packs weigh between 0.5LB and 15LB. The sensor is calibrated in such a way that it outputs 0V at 1LB applied force/weight. After the calibration, the sensor transfer function is given as 100mv/0.5LB. What is the sensor output DC voltage value if the measured weight is 3 LB? A. 0.2V B. -0.2V C. 0.4V D. -0.4V In the above question, assume that the sensor can measure from 0LB to 21 LB with an accuracy of Full-scale error.

n the packaging industry, assume that a strain gauge sensor is used to measure the weight of a food package. The strain gauge changes its output DC voltage value whenever some force/weight is applied on it. The food packs weigh between 0.5LB and 15LB. The sensor is calibrated in such a way that it outputs 0V at 1LB applied force/weight. After the calibration, the sensor transfer function is given as 100mv/0.5LB. What is the sensor output DC voltage value if the measured weight is 3 LB? A. 0.2V B. -0.2V C. 0.4V D. -0.4V In the above question, assume that the sensor can measure from 0LB to 21 LB with an accuracy of Full-scale error.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
> A Moving to another question will save this response. uestion 7 If a half wave rectifier is supplied using 240 V (rms), 50 Hz supply, then using constant voltage drop model, the average output voltage is equal to 152.79 V 108.04 V 76.17 V 107.8 V A Moving to another question will save this response hp brt sc f10
Clearly write the differences between the Metal Strain Gauges and Semiconductor Strain Gauges.
Select any diode from LTSpice Library. (The type of diode should either be RECTIFIER or SILICON) Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 85VAC - 50Hz, if the last number of your student number is ODD. Input Voltage should be 95VAC - 65Hz, if the last number of your student number is EVEN. Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
Can you help me with this homework problem? Constant voltage drop is Vd=0.7 What is the output volts of V? What is the current I going through the resistor? What is the diode current Id2? What is the diode current Id1? What are the states of two diodes D1 and D2?
A 1 - ∅ full-wave rectifier is made by using thyristors. If the peak value of the sinusoidal input voltage is Vm and the value of the delay angle is 45 degree, find the average value of output voltage Select one: a. 0.65 VM b. 0.85 VM c. 0.45 VM d. 0.25 Vm
ier quesuon Will save this response. Quèstion 6 Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to iL-DC =05A RL VLDC =20V 220V omsb 0.01 F 0.02 F 0.0167 F Hows b None of the above DEV Chp
10- The basic component of digital voltmeter are: a- AID converter and a counter. c-DIA converter and a counter. b- AD converter and a rectifier. d-Ramp generator and a counter. 11- A d.c voltmeter has a sensitivity of 1000 n/V when it measures half full scale in 100V range, the current through the voltmeter is: a- 100mA b- ImA c-0.5mA d-50mA 12- A DVM measure.... a- peak value. b-RMS value. c- Average value. d- peak to peak value. 13. The study of energy distribution across the frequency spectrum of a given electrical signal is done by a a-Distortion meter. b-wave analyzer. d-Q-meter. c-spectrum analyzer. 14. The harmonic distortion percentage is accurately measured by: a- VTVM. b- CRO. c- harmonic distortion analyzer. d- VOM.
A full-wave bridge rectifier is to be designed to produce a peak output voltage of 10 V, deliver 100 mA to the load, and produce an output with a ripple of not more than 7.5 percent. Assume that the frequency of the source is 50 Hz, and that a constant drop voltage model with Vp = 0.7 V is t of used. D1 D2 vs(1) RL vz(?) D3 D4 Source Rectifier Load a) Calculate the needed value of the load resistor R1. 1 b) Calculate the peak value of the voltage source which should be used V (t). [ c) What will be the value of the ripple voltage V7 [ d) Calculate the value of the required capacitor C. [ e) Explain in your own words the difference between the output with and without using the capacitor in the circuit above.
ZAIN IQ lI.. A docs.google.com The peak value of the input to a half- wave rectifier is 10 V. The approximate peak value of the output is 10 V O 10.7 9.3 O 3.18 O
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary. 110 V 00000 illlle Vp(sec) D3 D₂ D₁ R₁ 10 ΚΩ www1₁ Vp(out)
The input to a full-wave rectifier is 40 V AC (RMS). The load resistor is 10 ohms. The DC voltage at the output is: O A. 27 V O B. 18 V O C. 36 V O D. None of the other choices are correct O E. 21 V