H.Q 10A concrete pile 20 m long having a cross section of 0.46 m x 0.46 m isfully embedded in a saturated clay layer. For the clay, given: Ysat = 18kN/m3,0= 0, and cu = 80 kN/m2. Determine the allowable load that thepile can carry (FS = 3). Use the method to estimate the skinresistance.

Given data- Saturated Clay layer. Length of concrete pile (L) = 20 m Square cross-section = 0.46 m ×…

Н.О 10 A concrete pile 20 m long having a cross section of 0.46 m x 0.46 m is fully embedded in a saturated clay layer. For the clay, given: ysat = 18 %3D kN/m3,p= 0, and cu = 80 kN/m2. Determine the allowable load that the pile can carry (FS = 3). Use the A method to estimate the skin %3D resistance.

Н.О 10 A concrete pile 20 m long having a cross section of 0.46 m x 0.46 m is fully embedded in a saturated clay layer. For the clay, given: ysat = 18 %3D kN/m3,p= 0, and cu = 80 kN/m2. Determine the allowable load that the pile can carry (FS = 3). Use the A method to estimate the skin %3D resistance.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.12P

See similar textbooks

Similar questions

A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Redo Problem 12.20 using Vesics method, assuming that the skin friction is distributed uniformly along the shaft. 12.20 A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5 fill. FIG. 18.26 Negative skin friction
A concrete pile 16 in. 16 in. in cross section is shown in Figure P12.13. Calculate the ultimate skin friction resistance by using the a. method [use Eq. (12.61) and Table 12.11] b. method c. method Use R=20 for all clays, which are normally consolidated.
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
A 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Qp by a. Meyerhofs method b. Vesics method c. Coyle and Castellos method Use m = 600 in Eq. (12.28).
Refer to Figure 18.13. Given L1 = 1.5 m, L2 = 3 m; for the sand, =33, =16.5kN/m3, sat=19.0kN/m3; and, for the clay, c=50kN/m2, =0, sat=20kN/m3. Determine the depth of sheet pile required, allowing for a 50% increase from the theoretical estimate.
Solve Problem 12.13 using Eqs. (12.59) and (12.60). 12.13 A concrete pile 16 in. × 16 in. in cross section is shown in Figure P12.13. Calculate the ultimate skin friction resistance by using the α method [use Eq. (12.61) and Table 12.11] λ method β method Use for all clays, which are normally consolidated.
Redo Problem 18.10 using the method for estimating the skin resistance. 18.10 A concrete pile 15 m long with a cross section of 380 mm 380 mm is fully embedded in a saturated clay layer. For the clay, sat = 18 kN/m3, = 0, and cu = 80 kN/m2. Assume that the water table lies below the tip of the pile. Determine the allowable load that the pile can carry (FS = 3). Use the a method to estimate the skin resistance.
Following is the variation of N60 with depth in a granular soil deposit. A concrete pile 9 m long (460 mm x 460 mm in cross section) is driven into the sand and fully embedded in the sand. Estimate the allowable load-carrying capacity of the pile (Qall). Use FS = 4 and Meyerhof’s equations
A circular pile 0.45m in diameter and 15m long is embedded in a layer of dense sand. The soil has the following properties: Dry unit eight is 18 kN/m3 and saturated unit weight is 21 kN/m3 (water table is 4m below from the ground surface), Nq=85, k=1.25, tan αα = 0.45 and FS=2.5 a) Calculate the end bearing capacity b) Calculate the frictional resistance c) Calculate the allowable load
For the pile distribution below, determine the load Pp that the red pile will receive, in Ton. P = 254 Ton, d = 2 m, ex = 0.2 m, ey = 0.3 m, H = 1.3 m. ex, e and positive with the axes. Consider the self-weight of the head.