na wastewater treatment plant, 35 mg/L of ammonia was nitrified to oxidized nitrogen in the bioreactor. The inflow is 2 ML/d. What is the minimum rate the A recycle must run at to achieve an effluent oxidized nitrogen of 2.5 mg/L? The RAS is run at a ratio of 1:1 sewage to RAS return.

na wastewater treatment plant, 35 mg/L of ammonia was nitrified to oxidized nitrogen in the bioreactor. The inflow is 2 ML/d. What is the minimum rate the A recycle must run at to achieve an effluent oxidized nitrogen of 2.5 mg/L? The RAS is run at a ratio of 1:1 sewage to RAS return.

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter9: Toward Integrated Resources Management—environmental, Political, And Economic Issues

Section: Chapter Questions

Problem 9.1P

See similar textbooks

Related questions

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: Soils laboratory technician carries out a standard Proctor test on an SP-type soil and observes, at…

Q: 150 m long commercial steel pipe is to convey 30 L/s of oil (s=0.9, μ-0.038 N.s/m² from one tank to…

A: Given :

Q: (2) What is the reduction of the free-flow speed due to the given right-shoulder lateral clearance…

A: Lane Width Adjustment Correction Factor This Correction is applied when Lane Width is narrower than…

Q: Collars A and B slide along the fixed right-angle rods and are connected by a cord of length L = 4.3…

Q: 6 A 72 C W 2 T 30⁰ D B 12 A beam AB of length 1 and weight w supports a load W at its free end B and…

Q: Design a square base plate to support 12 mm thick pipe column with an inside diameter of 400 mm. The…

A: A very specialized field of civil engineering is structural design. It may be characterized as a…

Q: Q-f Calculate the settlement of the bridge pier shown in Fig. Q-f (page 3) due to primary…

Q: Cite 3 possible advantages of the bidding process in Section 3. (Construction project) 2. What is…

A: Solution: Bidding on construction projects is defined as one of the important aspects of…

Q: 4) A steel brace is subjected to following loads. Using the load combinations given in AISC 360-10,…

A: Given :

Q: Using superposition method, determine the maximum deflection of the beam shown below if it has a…

Q: From the figure below.assuming the support at A, B and C are rollers. 1.4 1.0 0.5 A Which of the…

A: Given data in question Beam Span member length To find out ILD reaction co ordinate NOte We will…

Q: = Steam enters a turbine at 30 bar, 300°C (u = 2750 kJ/kg, h 2993 kJ/kg) and exits the condenser as…

A: Find work output of turbine.

Q: 9 m 1 m 1 m 12 MN Pier: 3 m x 10 m 3 m 5 m Dense sand e = 0.45 E' = 55 MPa v' = 0.35 $ = 36°…

A: First of all we need to calculate the effective stress at the center of clay layer. then we will…

Q: 8. On a map of scale 1:75,000 the map distance measured between points A and B is 5.0 cm. If a…

A: Solve question 8 and 9

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: A closed traverse has the following data: LAT AB = +15.43, LAT BC = -7.04, LAT CD = -28.62, LAT DE =…

Q: Determine the force in members GF, FC, and CD of the cantilever truss. State if the members are in…

A: Using section method take the section in such a way so that it can divide into two half. A point…

Q: Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is…

Q: The relation between speed u (in km/h) and density k (number of vehicles / km) for a traffic stream…

A: Given data: The relation between speed and density, u=70-0.7k

Q: A 200mmx400mm rectangular beam has 5-20mm diameter rebar at the tension side and 2-20 diameter rebar…

A: Given values: width of beam, b = 200 mm depth of beam, D = 400 mm db (main bars) = 20 mm dbs…

Q: The backfill behind a retaining wall, located above the water table, consists of a sand of unit…

Q: Soils laboratory technician carries out a standard Proctor test on an SP-type soil and observes, at…

Q: Determine the x coordinate of the centroid of the plane area shown. a. 2cm b. 6.25 cm c. 2.3 cm d. 0…

A: Given, A plane area, Having sections (1) rectangle, size (12×6)cm (2) semicircle, radius of 4cm

Q: Concrete is required for walls of a building that will be Moderately exposed to freezing and…

A: Reference : ACI 311 Mix design All, tables are referred from ACI 311. Table : Relationship between…

Q: Determine the critical depth ( m ) and critical velocity

Q: 5. A uniform circular shaft, 750 mm long, carries 2 pulleys. The pulley on the left is 250 mm from…

Q: 11.4 The following are the results of a consolidation test on a sample of a clayey soil. Pressure, o…

A: Given :

Q: For the beam and the loading as shown in figure below, determine (1) the slopes at 2 and 3, (2) the…

A: Given data:- E=200 GPa=200×103 MPa=200×103 N/mm2I=4×106 mm4EI=200×103×4×106 Nmm2×mm4EI=800×109 N-mm2…

Q: A hydraulic jump occurs in a trapezoidal channel with side slope of 1V:2H and base width of 3.8m if…

A: Given Data: The slope of the channel is 1V: 2H. The base width of the trapezoidal channel is b = 3.8…

Q: Problem 4: Water at 80 degree flows in a conduit with a cross section shaped in the form of an…

A: The given data is as follows: Temperature of water=80∘FCross-sectional area of equilateral triangle…

Q: plz, solve all the parts of this problem. Plz, use ACI Code. Reinforced Concrete Design-1…

A: Solution: Given: Span = 24 ft b = 15 in d = 24 in DL = 1 K/ft LL = 1.4 k/ft fc = 3 ksi fy = 40 ksi

Q: 2000 lb A Member AB 20¹ Determine the internal force on: B D 1000 lb 560 lb 20' 2000 lb 1120 lb C…

Q: A flocculation tank contains 1800 m³ of water, which is mixed using paddles at an average velocity…

A: Given data in question Volume Velocity gradient Temperature Dynamic viscosity To find out…

Q: this is not a graded question and please base your answer on the given choices thank you

Q: 1. Determine the moments at B and C, then draw the moment diagram for the beam. Assume C is a fixed…

A: Given data:- E=200 GPa

Q: 3- Explain various factors affecting workability of concrete. 4- Explain the factors which effect on…

A: 3. Factors affecting workability of concrete water content : increase in cement content of concrete…

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

A: given- 2 simply supported beams-same material and same cross-sectionSame UDLspan of beam=2 m and 4…

Q: On a map of scale 1:75,000 the map distance measured between points A and B is 5.0 cm. If a sketch…

A: Find scale for sketch of same area

Q: Plz, solve the two parts of this question. Hydraulics. Reg.No: 5395 Question. a). A…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

Q: A beam is loaded and supported as shown, with M= 3160 ft lb, ₁ = 170 lb/ft and m₂ = 340 lb/ft. The…

Q: Given in the accompanying tabulation are the adjusted latitudes and adjusted departures of a parcel…

Q: A 5 m 16 16° 30° B E L C D L

Q: If f(x) = x(2x), then f'(x) is equal to: ○ 2 (2lnx + 1) © 2*(21n2 + x) © 2*(xln2 + 1) © 2*(In2 + 1)

A: Given: Question 1: f(x) = x (2x) , Find f'(x).

Q: What is the difference between dry pressing and semi-dry pressing of traditional ceramic parts?

A: Difference between dry pressing and semi dry pressing

Q: problem : Check whether the depth of a cantilever beam in the following dequate for controlling…

Q: A 150mm*50mm* 25mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's modulus…

Q: dimensions on the figure are a = 1.7 m, b= 1.6 m, c = 2.7 m, ww and label shear and bending moment…

Q: Two aluminum posts are located at equal distance from the middle steel post as shown. Take note that…

Concept explainers

Integrated Solid Waste Management

Integrated Solid Waste Management (ISWM) is a thorough waste suppression, compost, removal and recycling Program. An effective ISWM system considers how to suppress, manage and recycle solid waste in a manner that is most efficiently to protect human health and the surrounding. ISWM system requires evaluation of public wants and demands and then selecting and merging the most effective waste management activities for the proposed demands. The main ISWM activities for solid waste management are Waste prevention, Recycling and Composting, and Combustion and Removal and waste collection in a properly planned, constructed, managed and mitigated landfill areas. Each of these requires careful designing, financing, accumulation, and delivery of activities.

Question

na wastewater treatment plant, 35 mg/L of
ammonia was nitrified to oxidized nitrogen in
the bioreactor. The inflow is 2 ML/d. What is the
minimum rate the A recycle must run at to
achieve an effluent oxidized nitrogen of 2.5
mg/L? The RAS is run at a ratio of 1:1 sewage to
RAS return.
I need to know how to work out the answer
please

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 : Introduction

VIEW

Step 2 : Calculation of Minimum Recycle Rate :

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A waste with a 5-day BOD (BOD)=200mg/L and k = 0.1 day¹ is discharged to a river at a rate of 1 m/s. The river has flow rate of 9 m/s and a background ultimate BOD (Lo) of 2 mg/L upstream of the discharge. (a) Calculate the ultimate BOD (Le) of the waste. (b) Furthermore, assuming instantaneous mixing after discharge, calculate Lo of the river water after it has received the waste. Ans.: (a) Ultimate BOD of wastewater = 508.3 mg/L, (b) Ultimate BOD of river water after discharge of waste-52.63 mg/L.
Read the question carefully and give me right solution according to the question. Determine the diameter of a trickling filter for a wastewater flowing at the rate of 12900 m3/day. The influent BOD (So) concentration for the wastewater is 129000 mg/l, whereas desirable effluent BOD should be as per NEQS.
A conventional activated-sludge system treats 11,000 m3/day of wastewaterin an aeration tank with a volume of 3400 m3. The BOD after primary clarification is 180mg/l. Given the operation conditions below, calculate the sludge residence timeMLVSS in the rector = 2,100 mg/lMLSS = (1.25)*MLVSSQw = 160 m3/daySVI = 125 mL/g (Ans. SRT = 7.0 days)
Plz, solve this problem one by one and show all the steps. Environmental Engineering-2 An activated sludge process is to be designed to treat a sewage flow of 8640 m3/day with BOD of 200 mg/l from a primary clarifiers using F : M = 0.4 per day and MLSS of 3000 mg/l calculate volume of aeration tank if SVI is 100. How much sludge should be returned (Qr)?
The DO of a river is 5.9 mg/L just downstream from a wastewater outfall. The mix ofriver and wastewater has a BOD of 25 mg/L. The DOs is 9.2 mg/L and the kd = 0.22 / day. a. estimate the rearation coefficient assuming a river speed of 0.20 m/s and anaverage depth of 3.5 m b. find the critical distance downstream where DO is a minimum c. what percent of BOD has to be removed from wastewater to maintain > 5mg / L DOif it is the only source of river BOD
15 mL of raw wastewater wasadded into a 300-mL BOD bottle, which was then filled up with 285 mL pure water. The DO concentration in the mixed sample before incubation is 7.8 mg/L. The sample wasincubated for 5 days and the final DO wasfound to be 2.4 mg/L. What is theBOD5of the raw wastewater?
Plz, solve what you have been asked in this problem by giving detail information. Environmental Engineering-2 Determine the Aeration Basin Dimensions for a town of 30,000 population. Mixed Liquor Suspended Solids is 3000 mg/L. The BOD Loading rate is 0.48 kg/ (?3 –day), Sludge Volume Index is 100 mL/g; Return sludge is 40%; the concentration of BOD is 0.091 Kg/(Capita –day). Primary sedimentation tank remove 40% of BOD.
As an operator of a wastewater treatment facility, you have learned that your plant runs well at an SRT (based on MLVSS (X) in the aeration basin) of 12 days. If today’s MLVSS (X) concentration is 2,700 mg/L and the RAS (Xr) concentration is 5,500 mg/L, how many L of sludge should you waste from the secondary clarifier today? Other design conditions: Average influent flow = 12,000 m3/d Influent soluble BOD = 150 mg/L Required effluent TSS = 30 mg/L Aeration tank Volume = 1,000 m3
Please calculate the ThOD, COD, and ultimate BOD of a wastewater containing (a) 500 mg/L acetate (CH3COOH), which is fully biodegradable; or (b) 500 mg/L oil (C40H80), which is not biodegradable.
A wastewater treatment plant has been operating with the following specifications:flow rate = 7,630 m3/d, aeration tank volume = 1,270 m3, mixed liquor volatile suspendedsolids = 2,600 mg/l. The soluble BOD in the plant influent used to be 133 mg/l, but hasrecently changed to 222 mg/l. What is the new MLVSS this plant should use to maintain thesame F/M ratio as before? (Ans. Xnew = 4,340 mg MLVSS/l)
You’re working on a preliminary design for a water treatment plant expansion for Fell City. The required capacity is 12 MGD (million gallons per day). The TSS of the sedimentation basin effluent is 16 mg/L of TSS. Assume the effluent TSS is 0 mg/L. (a) Based on a filtration rate of 2 gpm/ft2, how big (area) must the filters be? (b) If 3% of the treated water is used for backwashing, what would the backwash TSS be? (Set up a mass balance analysis.) (c) How many tons of sludge (dry solids) would be generated in 30 days? Answers: 4170 ft2, 533 mg/L, 24 ton
A 76000 m'id domestic waste discharge has a concentration of 22 mg/L of ammonia nitrogen. If the receiving stream contains 1.5 mg/L and the maximum allowable concentration is 3.5 mg/L, compute the dilution of streamflow required in m'/s.