Name: Surname: Student ID: ME 216 MECHANICS OF MATERIALS QUIZ # 2 QUESTION σ (MPa) 490 420 350 280 210 140 70 25.03.2019 (mm/mm) 0 0.0008.002 0.004 0.006 0.008 0.010 A tension test was performed on a 7075-T6 aluminum tensile test specimen. The results are given in the figure above. According to this data, find: a. Young modulus of the material, b. Yield stress of the material (be careful, there is no any sharp yield point), c. Modulus of the resilience, d. If the material is stressed up to 420 MPa stress, what is the permanent elongation remained in the material if its length is 90 mm. e. For a 20 mm diameter bar made up of from the same material, what is the maximum load that can be applied without plastic deformation. ANSWER E=D ٤ E- 70.106 6= 70 MPa at ε = 0,0009 = 77,776 Pa 0,000 9

Name: Surname: Student ID: ME 216 MECHANICS OF MATERIALS QUIZ # 2 QUESTION σ (MPa) 490 420 350 280 210 140 70 25.03.2019 (mm/mm) 0 0.0008.002 0.004 0.006 0.008 0.010 A tension test was performed on a 7075-T6 aluminum tensile test specimen. The results are given in the figure above. According to this data, find: a. Young modulus of the material, b. Yield stress of the material (be careful, there is no any sharp yield point), c. Modulus of the resilience, d. If the material is stressed up to 420 MPa stress, what is the permanent elongation remained in the material if its length is 90 mm. e. For a 20 mm diameter bar made up of from the same material, what is the maximum load that can be applied without plastic deformation. ANSWER E=D ٤ E- 70.106 6= 70 MPa at ε = 0,0009 = 77,776 Pa 0,000 9

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 151 kN. - Length of the specimen is 23 mm. - The yield strength is 79 kN/mm2. - The percentage of elongation is 45 %. Determine the following (i) Diameter of the specimen, ii) Final length of the specimen, iii) Stress under an elastic load of 17 kN, iv) Young's Modulus if the elongation is 2.4 mm at 17 kN and (v) Final diameter if the percentage of reduction in area is 24 %. Find: 1)Stress at the elastic load (in N/mm2) 2)Young's Modulus of the Specimen (in N/mm2) 3)Final Area of the Specimen at Fracture (in mm) 4)Final Diameter of the Specimen after Fracture (in mm)
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 151 kN. - Length of the specimen is 23 mm. - The yield strength is 79 kN/mm2. - The percentage of elongation is 45 %. Determine the following (i) Diameter of the specimen, ii) Final length of the specimen, iii) Stress under an elastic load of 17 kN, iv) Young's Modulus if the elongation is 2.4 mm at 17 kN and (v) Final diameter if the percentage of reduction in area is 24 %. THE QUESTION IS : FIND THE Final Diameter of the Specimen after Fracture (in mm)????
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 159 kN. - Length of the specimen is 29 mm. - The yield strength is 82 kN/mm2. - The percentage of elongation is 47 %. Determine the following (i) Diameter of the specimen, ii) Final length of the specimen, iii) Stress under an elastic load of 19 kN, iv) Young's Modulus if the elongation is 2.8 mm at 19 kN and (v) Final diameter if the percentage of reduction in area is 21 %. Solution Initial Cross-sectional Area (in mm2) Answer for part 1 The Diameter of the Specimen (in mm) Answer for part 2 Final Length of the Specimen (in mm) Answer for part 3 Stress at the elastic load (in N/mm2) Answer for part 4 Young's Modulus of the Specimen (in N/mm2) Answer for part 5 Final Area of the Specimen at Fracture (in mm) Answer for part 6 Final Diameter of the Specimen after Fracture (in mm)
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 152 kN. - Length of the specimen is 20 mm. - The yield strength is 86 kN/mm2. - The percentage of elongation is 48 %. Determine the following (i) Diameter of the specimen, ii) Final length of the specimen, iii) Stress under an elastic load of 10 kN, iv) Young's Modulus if the elongation is 2.2 mm at 10 kN and (v) Final diameter if the percentage of reduction in area is 28 %. Solution Initial Cross-sectional Area (in mm2) Answer for part 1 The Diameter of the Specimen (in mm) Answer for part 2 Final Length of the Specimen (in mm) Answer for part 3 Stress at the elastic load (in N/mm2) Answer for part 4 Young's Modulus of the Specimen (in N/mm2) Answer for part 5 Final Area of the Specimen at Fracture (in mm) Answer for part 6 Final Diameter of the Specimen after Fracture (in mm) Answer for part 7
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 157 kN. - Length of the specimen is 23 mm. - The yield strength is 89 kN/mm2. - The percentage of elongation is 45 %. Determine the following (i) Diameter of the specimen, ii) Final length of the specimen, iii) Stress under an elastic load of 18 kN, iv) Young's Modulus if the elongation is 1.3 mm at 18 kN and (v) Final diameter if the percentage of reduction in area is 25 %. Solution: Initial Cross-sectional Area (in mm2) The Diameter of the Specimen (in mm) Final Length of the Specimen (in mm) Stress at the elastic load (in N/mm2) Young's Modulus of the Specimen (in N/mm2) Final Area of the Specimen at Fracture (in mm) Final Diameter of the Specimen after Fracture (in mm)
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 150 kN. - Length of the specimen is 24 mm. - The yield strength is 78 kN/mm2. - The percentage of elongation is 42 %. Determine the following iii) Stress under an elastic load of 14 kN, iv) Young's Modulus if the elongation is 1.7 mm at 14 kN and (v) Final diameter if the percentage of reduction in area is 26 %. I wont answer for this three questions only: 1)Final Area of the Specimen at Fracture (in mm) 2)Final Diameter of the Specimen after Fracture (in mm) 3)Initial Cross-sectional Area (in mm2)
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 147 kN. - Length of the specimen is 28 mm. - The yield strength is 75 kN/mm2. - The percentage of elongation is 49 %. Determine the following (i) Diameter of the specimen, ii) Final length of the specimen, iii) Stress under an elastic load of 16 kN, iv) Young's Modulus if the elongation is 1 mm at 16 kN and (v) Final diameter if the percentage of reduction in area is 22 Final Area of the Specimen at Fracture (in mm) Final Diameter of the Specimen after Fracture (in mm) Initial Cross-sectional Area (in mm2)
Mild steel 1 Young;s modulus 1219.5 Yield strain and stress (0.4101,500.08) Failure stress and strain :not able to find because the given data shows the experiment did not reach the failure point. if the material stress and strain does not reach a failure point ,what dose it means , does it means that the material is more stronger?
The following data were obtained from a standard tensile stress test on a mild steel specimen. Graph the result and determine proportional limit stress and Young’s Modulus.
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 157 kN. - Length of the specimen is 23 mm. - The yield strength is 89 kN/mm2. - The percentage of elongation is 45 %. Determine the following Diameter of the specimen, Final length of the specimen, Stress under an elastic load of 18 kN, Young's Modulus if the elongation is 1.3 mm at 18 kN and Final diameter if the percentage of reduction in area is 25 %. Fine this ans 1-Initial Cross-sectional Area (in mm2) 2-The Diameter of the Specimen (in mm) 3-Final Length of the Specimen (in mm) 4-Stress at the elastic load (in N/mm2) 5-Young's Modulus of the Specimen (in N/mm2) 6-Final Area of the Specimen at Fracture (in mm) 7-Final Diameter of the Specimen after Fracture (in mm)
*Only need Question 10.12 answered. Thank you! 10.11 The elasticity of a cylindrical sample of an unknown material is to be tested. The sample is 40 cm long and has a cross-sectional area of 2.5 cm2 . The sample is hung vertically and a 50 kg weight is attached to its free end. It is found that the sample stretches to a length of 40.1 cm. (a) What is the tensile stress on the sample? (b) What is the tensile strain? (c) What is Young’s modulus for this material? 10.12 (a) Bone has a tensile Young’s modulus of ?tensile = 16 × 109 N m−2 . If the sample of unknown material in Problem 10.11 was replaced with an identical sample of bone, what would the length increase of the bone be? (b) Bone has a compressive Young’s modulus of ?comp = 9 × 109 N m−2 . If the 50 kg weight was used to compress the sample rather than stretch it, how much would the length of the sample change?
Three identical fatigue specimen ( denoted A ,B and C ) are fabricated from none ferrous alloy .Each one is subjected to one of the maximum- minimum stress cycles listed in the following table, the frequency is the same for all the three tests.. Which of the following samples will have the longest life and the shortest life Specimen Stress,max ( MPa) Stress , min (MPa) A +450 -150 B +300 -300 C +500 -200