Neglect bias, decoupling and coupling components. 2. An amplifier has the following parameters: input resistance, 470 k2; output resistance, 8.2 k2; opencircuit voltage gain 50. A signal source having an e.m.f. of 75 uV and negligible internal resistance is connected to the input of the amplifier. The output is connected to a 10 kQ resistive load. Draw the equivalent circuit and hence determine: (a) the output voltage developed across the load; (b) the current gain (c) the voltage gain.

Neglect bias, decoupling and coupling components. 2. An amplifier has the following parameters: input resistance, 470 k2; output resistance, 8.2 k2; opencircuit voltage gain 50. A signal source having an e.m.f. of 75 uV and negligible internal resistance is connected to the input of the amplifier. The output is connected to a 10 kQ resistive load. Draw the equivalent circuit and hence determine: (a) the output voltage developed across the load; (b) the current gain (c) the voltage gain.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the operational amplifier circuit shown below. Assume the operational amplifier in the circuit is ideal. Determine the expression for the output signal, Vout, in terms of Vin,R1 and R2. Given the expression of the circuit [above’s output signal is Vout =3 − 0.5Vin, what is the maximum and minimum voltage that the input signal can have before the operational amplifier saturates.
Consider the amplifier shownbelow. (a) Draw the small signal equivalent circuit assuming that the capacitorsare short circuits for the signal.(b) Derive an expression for the voltage gain.(c) Find IDQ if R = 100kΩ, Rf = 100kΩ, RD = 3kΩ, RL = 10kΩ, VDD =20 V, Vto = 5 V, and K = 1 mA/V 2. Determine the value of gm at the Q point.(d) Is this amplifier inverting or noninverting?
Show the manual solution of the simulated values for the given non-inverting amplifier below
For the circuit shown, RI = 1Ω k , Rin =20Ω k , Rout = 60Ω , and RL = 2 Ωk . Whatvalue of A is required to produce a voltage gain of74 dB if the amplifier is to be an inverting amplifier(θ = 180◦)?
For the amplifier as shown, VDD = 12 V, VSS = 12 V, ISS = 20 μA, and RD = 820 kΩ. Assume IDSS = 1 mA and VP = +2 V. (a) What are the output voltages υo for the amplifier for υ1 = 0V and υ1 = 20 mV? (b) What is the maximum permissible value of υs?
We examined the common source amplifier shown in the figure in the 5th experiment. The capacitances have high enough value to assume them short circuit for the small-signal conditions. The gain of the amplifier for no-load condition is measured as 60. When a load resistance RL = 13 kΩ is connected, the gain is measured as 10. Calculate the output impedance of the amplifier, Rout.
What are Aυ, Ai , Rin, Rout, and the maximum amplitude of the signal source for the amplifier shown if R1 = 20 kΩ, R2 = 62 kΩ, RE = 3.9 kΩ, RC = 10 kΩ, and VCC = 12 V? Use βF = 75. Compare Aυ to our rule-of-thumb estimateand discuss the reasons for any discrepancy.
For the amplifier shown below, find the expressions for Vout / isig, Rin and Rout.
Draw the dc equivalent circuit and find the Q-point for the amplifier shown. Assume Kp = 400 μA/V2, VT P = −1 V, VDD = 15 V, R1 = 2 MΩ, R2 = 2 MΩ, RD = 24 kΩ, and R4 = 22 kΩ.
The following Common Emitter (C.E.) amplifier is biased with a currentsource I. It has β = 100, VA = ∞, VT = 25mV, and rπ = 25kΩ. Draw the small signal equivalent circuit including the Hybrid-π with the βIb currentsource model. Label the input (Rin), output (Rout), and base (Rib) resistances. Find Rib, Rin, Rout, and the voltage gain (vo/vsig).
Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: 1- Determine the Q point, then illustrate it on the transistor I-V characteristic curves. 2- Is the transistor in the active region? Explain thoroughly. 3- Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. 4- Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. 5- Calculate the current gain, the input resistance, and the output resistance.
(a) A source follower is drawn as a two-port as shoen. Calculate Gm and Gr for this amplifier in terms of the small-signal parameters. Compare the two results. (b) What are the values of Gm and Gr if RG = 1 MΩ, RD = 50 kΩ, gm = 500 μS, and ro = 450 kμ?