ng discussed topics below. Absolute Dependent Motio Relative Motion Force and Acceleration : Equation of Motion Force and Acceleration : Rectangular Components Force and Acceleration : Normaland Tangential

Q: Determine the member force GC? 400 N 3 m LA B 4 m 4 m -4 m 1200 N

A:

Q: Item 6 of 9 The disk rolls without sliding on the fixed horizontal surface. At the instant shown,…

A: Instantaneous center is that point which is momentarily at rest.

Q: A single rolling load of 40 kN rolls from left end along a simply supported girder of span 20 m. The…

A:

Q: Based on the figure below, a steel rod was fitted on the copper tube and was fixed with a washers…

A:

Q: A soil sample is oven-dried from its liquid limit state to its dry state causing a volume change of…

A:

Q: Which of the following is a disadvantage of bolted connections? Requires more labor to install O…

A: The bolted joint having simple design, which helps to identify the joints are easy than other joint…

Q: Using the value of Cd, which you have obtained by experiment, determine the throat diameter of a…

A: Solution  Given Data:- Pipe Diameter = 0.6 m  Differential Head = 0.8 m Flow Rate = 0.4 m3/s  Find-…

Q: Plot the curve and show solution. A vertical summit curve is having tangents which intersects at…

A:

Q: F1 F2 A L1 L2

A:

Q: Water flows through a pipe at 5 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3…

A:

Q: 18. Determine the capitalized cost of a bridge whose cost is P200 Million and its life is 50 years,…

A:

Q: Example 3.12. The lever ABC of a component of a machine is hinged at B, and is subjected to a system…

A: Draw the Free body diagram of the lever and resolve all applied forces along horizontal and vertical…

Q: What diameter of a standard, sharp-edge orifice will be required to produce a discharge of 1.25 cfs…

A:

Q: A steel tire has a dimensions indicated in the figure below. At 78 degrees Celsius, the said tire…

A:

Q: J.omm 1.0 Mm to

A:

Q: Given are the following: fc’ = 35 MPa fpu = 1,500 MPa Aps = 1,800 mm2 fpy = 1,320 MPa Use…

A: Reinforcement Index: The product of the volume fraction and the aspect ratio of the given fibers is…

Q: In 28.5 secs, 35,579 L of water is collected. The length of the rectangular weir is 2.15 m, the…

A:

Q: What is LAP SPLICING? Illustrate a figure and explain it thoroughly

A: A lap is when two pieces of reinforcing bar (rebar) are overlapped to create a continuous line of…

Q: A triangular, sharp crested weir with end contraction of 1.4 m long and the upstream depth is 2.35.…

A:

Q: Cement dust is characterized by very fine particulates. The exhaust gas temperatures from a cement…

A: Cement kilns produce hot exhaust gases which needs to be controlled by an appropriate devices.

Q: Dráw the moment and shear diagram for the given loadings using the method of area. Note:…

A: Consider the figure,

Q: How many zero force members are in the truss below?

A:

Q: The bolted connection shown is a bearing type connection. Which of the following best gives the…

A: Answer We are given M20 A 490 group bolts Number of bolts = 6  Calculations shown below

Q: rmine the maximum value of ecting points B and D rmine the maximum value of age normal stress points…

A: solution of above problem is below:

Q: Let the number of trips from i to j is 5000, and three modes are available which has the…

A:

Q: According to Euler's column theory, the crippling load for a column of length (I) fixed at both ends…

A:

Q: II - Three Moment Equation 2. Determine the reactions at the supports for the given beam. The moment…

A:

Q: Prob. 4 Consider a slender 2 meter uniform homogeneous 7-kg bar that rests on, and makes 45-degree…

A: For no slipping to occur the bar must be in equilibrium. Draw the FBD showing all forces. Then using…

Q: Find the water content in the following calculations 1- Liquid limit Determination: TT Weight of…

A: we are required to find the water content in each trial. student must note that the 4th column is…

Q: P=51

A:

Q: Write the shear and moment equations for the following using the algebraic method. Draw the shear…

A: Calculation of vertical reactions

Q: In the figure below, a fluid with a specific gravity of 0.77 is flowing. The mass flow rate is…

A:

Q: Hard water can be a serious problem in industry, especially when used for heating. In a so called…

A:

Q: Determine the relative angle of twist of gear D relative to gear A (in degrees). * Your answer What…

A:

Q: 4. Angle to the right of line DE= 6. Azimuth from South of line BC •

A:

Q: 1. Channel section and angular section with longer leg vertical Given: Channel section…

A: As per bartleby guide line I will answer only one section and 3 sub parts. So other sections are…

Q: FROM THE GIVEN FIGURES BELOW OETERMINE THE FOLLOWING : a. SHEAR AND MOMENT EQUATION OF EACH SECMENT.…

A:

Q: A simply supported steel joist with a 4.0 m effective span carries a uniformly distributed load of…

A:

Q: 1. A large soil sample obtained from a borrow pit has a wet mass of 26.50kg. the in - place volume…

A:

Q: Explain comprehensively when is it allowable to use static lateral force procedure

A: Static lateral force procedure is used to develop and distribute equivalent static lateral loads on…

Q: A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars…

A:

Q: Calculate the safe concentrated live load at the free end for a rectangular cantilever beam 3 m long…

A:

Q: What is the relative density of a sand in a certain locality being tested at 98% standard proctor…

A: Maximum dry density = 18.8 Kn/m3 Minimum dry density = 14 kn/m3 Relative Compaction = 0.98 First…

Q: Example 4.5 4.8 m. The member is to be used in a transmission line tower and is as shown ends are…

A:

Q: C 6 m B A 5 m 3 m 6 m 3 m Fiq 23 - Prob 23

A:

Q: Calculate the weight of moist gravel that should be in a batch if the design mix requires concrete…

A:

Q: 23. An equipment costing P250,000 has an estimated life of 15 years with a book value of P30,000 at…

A:

Q: 3-27. AW18X 40 consisting of A992 steel and having two lines of 1-in Ø bolts in each flange. There…

A:

Q: The compound shaft shown is attached to rigid supports. b. Bronze "B Steel For the bronze For the…

A: Given, SSbronze = 45 MPa SSsteel = 55 MPa

Q: construction site environment

A: Construction quality is a critical factor that directly affects the growth of any construction…