Note: Kindly provide a solution pls. The answer is already provided. Thank you! 1.7 A hemispherical tank having a radius "R" contains liquids A and B that have depths of 5 cm. and 10 cm. respectively. Liquid A is on top of Liquid B. If the volume of liquids A and B are equal, determine the volume (cm^3) of the hemisphere that contains the two liquids. Ans: 12,905.7402

Note: Kindly provide a solution pls. The answer is already provided. Thank you! 1.7 A hemispherical tank having a radius "R" contains liquids A and B that have depths of 5 cm. and 10 cm. respectively. Liquid A is on top of Liquid B. If the volume of liquids A and B are equal, determine the volume (cm^3) of the hemisphere that contains the two liquids. Ans: 12,905.7402

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 26P: SAE 30 oil is contained in a cylinder with inside diameter of 1 in. and length of 1 ft. What is the...

See similar textbooks

Similar questions

A conical tank 4.5m on top and 4,7m tall has a 60mm diameter orifice at its bottom for its outlet. Assume C = 0.63. The tank is filled with 7000 liters of water. What is the depth of the water in the tank in meters? How long will it take to drain the content of the tank in minutes? show solution and diagram
A rectangular tank 3 m x 4 m is 5 m high with 2 orifices placed at a vertical distances of 0.5 m and 1m from the bottom respectively. Both orifices are 100 mm diameter with C=0.607. Determine the: show complete solution a. How long will it take to lower the water at tank by 2 m in seconds?b. How long will it take for the water surface to be at the same level as the upper orifice in seconds?
A storage vessel for gasoline (SG=0.68) is a vertical cylinder10m in diameter. If it is filled to a depth of 6.75m, calculatethe weight and mass of the gasoline. m=? w=?
An engineer sees a water flow through a 0.4 km long and 200 mm diameter pipe having a roughness of 0.0015 mm at 0.075 cubic meter per second. Assuming that the property of H2O is u = 0.001 Nm/sec and p = 1 g/cu.m. He is bored, so he wanted to calculate the following, help him. a. the pressure drop cause of friction b. velocity of H2O in the pipe c. find the Re?
A hollow cylinder 1.0m in diameter and 2m long weighs 3825N. How many KN of lead weighing 110KN/m³ must be fastened to the outside bottom to make the cylinder float vertically with 1.5msubmerged in freshwater?
Q5. A brass cube “R” inch on a side weighs (Rx10)lb.Hold this cube in equilibrium underwater by attaching light foam buoy to it. If the unit weight of foam is 4.5 lb/ft3, calculate the minimum required volume of the buoy? (where R is ) 32)?
Determine the rate of flow of water through a pipe of diameter 10 cm and length 60 cm when one end of the pipe is connected to a tank and other end of the pipe is open to the atmosphere. The height of water in the tank from the centre of the pipe is 5 cm. Pipe is given as horizontal and value of f= 0.01. Consider minor losses.
Water leaks from a cylinder with axis vertical through a small orifice in its base at a rate proportional to the square root of the volume remaining any time. If the cylinder contains 64 gal. initially and 15 gal. leak out the first day, when will 25 gal. remains? How much will remain at the end of 4 days?Ans. 3 days, 16 gal.
6. Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown in figure. Determine the pressure difference Pfresh water- Psea water= ?(kPa) between the two pipelines. Take the density of seawater at that location to be P = 1035 kg/m³. (2 decimal)
Need answer ASAP. Please show your solution in detailed and clear. I. If a certain liquid weighs 6.80 kN/m³. Compute the following: 1) Mass density in kg/m³ . 2) Specific volume 3) Specific gravity relative to water at 20°C?
Given below are pipe lengths, sizes, and connections. All pipes have a friction factor of 0.020. If the flow from A to B is 8 cfs, Determine the head loss in feet in PIPE 5. *23.8062*9.0254*1.0666*2.6570 Determine the flow in the upper branch pipe Q2 in cubic feet per second. *2.6667*2.3809*4.8840*12.4747 Determine the head loss in feet in PIPE 2. *3.4373*8.0165*9.2849*10.4720 Determine the total head loss in feet between the inlet A and the outlet D. *9.2849*13.1625*17.3474*35.9163
2. What volume flow rate in gallons per minute of oil (sg = 0.80) is in the system?