Note : This question was already there but wrong... If you don't know the solution please leave it but don't copy from other experts solution. Copied solution eligible for dislike. A glass tube 1.60m long and having a diameter of 2.5cm is inserted vertically into a tank of oil (specific gravity 0.80) with the open end down and the closed end uppermost. If the open end is submerged 1.30m from the oil surface, determine the height to which the oil will rise in the tube. Assume barometric pressure is 100 kPa and neglect vapor pressure.

Note : This question was already there but wrong... If you don't know the solution please leave it but don't copy from other experts solution. Copied solution eligible for dislike. A glass tube 1.60m long and having a diameter of 2.5cm is inserted vertically into a tank of oil (specific gravity 0.80) with the open end down and the closed end uppermost. If the open end is submerged 1.30m from the oil surface, determine the height to which the oil will rise in the tube. Assume barometric pressure is 100 kPa and neglect vapor pressure.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter27: Commercial Ice Machines

Section: Chapter Questions

Problem 30RQ

See similar textbooks

Similar questions

Design and study of floating Roofs for Oil storage tanks(*50 mm of rain above the roof) . what the Challenges and Solutions of that ?
A vertical tube 3.0m long its upper end closed and the lower end open, has its lower end submerged in a tank of water to such a depth 150mm. Neglecting vapor pressure, how far is the lower end of the tube below the water surface in the tank? SHOW COMPLETE SOLUTION. NEED ASAP. THANK YOU.
Compute the capillary effect of immersion in mercury of a 5 point glass tube of 6mm internal diameter given the surface tension value is 0.51 N/m, the specific gravity value is 13.55 and the angle of contact is 140 degrees. Express your answer in the appropriate SI unit.
Thin walled pressure vessel 3. Please provide proper discussion and illustration. Clear and complete solution please thank you.
Thin walled pressure vessel 4. Please provide a proper discussion and illustration also complete and clear solution please thank you.
Compute the capillary effect of immersion in mercury of a glass tube of 6mm internal diameter given the surface tension value is 0.51N/m, the specific gravity value is 13.55 and the angle of contact is 140 degrees. Express the answer in the appropriate SI unit.
A sleeve of 10cm encases a vertical metal rod 3.0cm in diameter with radial clearance of 0.02mm. if when immersed in oil of viscosity 6.0 poise , the effective weight of the sleeve is 7.5N , will the sleeve slide down the rod and if so, at what velocity?
Answer the question considering the information given in the picture b)Calculate the pressure difference between the two points 30 cm apart, where the piezometric tubes are located.
solve for the time it takes to reduce the heigt of water in a 1-m diameter cylindrical tank by 30% through a 5-cm hole at the bottom; The tank was initially filled to 3/4 of its total height Use Toricelli's law
A weight, as shown in figure Q1b-(a) has to move at constant velocity of 2 m/s on aninclined surface with a coefficient of friction of 0.27. The width of the block is 20 cm By applying a thick oil film as shown in figure Q1b-(b), the force required topush the block reduced by 45%. If dynamic viscosity of the oil is 12 cP,determine the oil layer thickness.
5b.please explain breifly in type form Describe the relation between fluid friction and heat transfer
In Fig the 20 ° C water and gasoline surfaces are opento the atmosphere and at the same elevation. What is theheight h of the third liquid in the right leg?