Now you will use the ruler to measure the dimensions of a block of pure aluminum metal. Make sure you report both the uncertainty and an estimated digit with your answers. V [ Select ] 1 21 1.5 cm +/- .1 cm cm 1.38 cm +/- .01 cm What is the best measurement of the length of this block? 135 cm al 01 om

Now you will use the ruler to measure the dimensions of a block of pure aluminum metal. Make sure you report both the uncertainty and an estimated digit with your answers. V [ Select ] 1 21 1.5 cm +/- .1 cm cm 1.38 cm +/- .01 cm What is the best measurement of the length of this block? 135 cm al 01 om

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter1: Introduction: The Nature Of Science And Physics

Section: Chapter Questions

Problem 20PE: (a) A person's blood pressure is measured to be 1202 mm Hg. What is its percent uncertainty? (b)...

See similar textbooks

Similar questions

A block of gold has length 5.62 cm. width 6.35 cm, and height 2.78 cm. (a) Calculate the length times the width and round the answer to the appropriate number of significant figures. (b) Now multiply the rounded result of part (a) by the height and again round, obtaining the volume. (c) Repeat the process, first finding the width limes the height, founding it, and then obtaining the volume by multiplying by the length. (d) Explain why the answers dont agree in the third significant figure.
(a) A person's blood pressure is measured to be 1202 mm Hg. What is its percent uncertainty? (b) Assuming the same percent uncertainty, what is the uncertainty in a blood pressure measurement of 80 mm Hg?
(a) How many significant figures are in the numbers 99 and 100? (b) If the uncertainty in each number is 1, what is the percent uncertainty in each? (c) Which is a more meaningful way to express the accuracy of these two numbers, significant figures or percent uncertainties?
(a) If your speedometer has an uncertainty of 2.0 km/h at a speed of 90 km/h, what is the percent uncertainty? (b) If it has the same percent uncertainty when it reads 60 km/h, what is the range of speeds you could be going?
A sidewalk is to be constructed around a swimming pool that measures (10.0 0.1) m by (17.0 0.1) m. If the sidewalk is to measure (1.00 0.01) m wide by (9.0 0.1) cm thick, what volume of concrete is needed and what is the approximate uncertainty of this volume?
Units and Standards What is the difference between a base unit and a derived unit? (b) What is the difference between a base quantity and a derived quantity? (c) What is the difference between a base quantity and a base unit?
hi , may i ask whether my calculation is correct or not but my teacher said it has to be si unit for density ? and if i convert to si unit , i dont get the answer for the uncertainty , please help me ?
. Suppose [V] = L3, [ρ]=ML–3,[ρ]=ML–3, and [t] = T. (a) What is the dimension of ∫ρdV?∫ρdV? (b) What is the dimension of dV/dt? (c) What is the dimension of ρ(dV/dt)? I'm not sure what this is asking. Thank you for the assistance.
(I) What are the dimensions of density, which is mass per volume?
The first several digits of p, the ratio of the circumference tothe diameter of a circle, are p = 3.14159265358979c. What isp to (a) three significant figures, (b) five significant figures, and(c) seven significant figures?Section 1-5 Converting
In the following problem I am asked to calculate a volume respecting the rules of significant figures: v=(4/3)pi (R^3)Where R=4.5cmHow should I do the calculation taking into account the significant figures? Should I do the direct calculations and at the end use as the number of significant figures the number that has fewer figures after the decimal point?or parse R separately first? applying the same ruleFirst of all, Thanks.
1. The following data are the measurements of the dimensions of a box: l = 8.6 ± 0.5 cm h = 20.19 ± 0.01 mm w = 0.75 ± .02 mHow should the volume of the box be reported (central value ± uncertainty) incm3? Show solution.2. If the accepted value of the volume of the box in the previous question is 1300 cm3, is the measurement acceptable? Explain.