A sand layer of the cross-sectional area shown in the figure has been determined to exist for a 800-m length of the levee. The hydraulic conductivity of the sand layer is 1.65 m/day. Determine the quantity of water which flows into the ditch in m3/min.

A sand layer of the cross-sectional area shown in the figure has been determined to exist for a 800-m length of the levee. The hydraulic conductivity of the sand layer is 1.65 m/day. Determine the quantity of water which flows into the ditch in m3/min.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.14P

See similar textbooks

Related questions

Q: the following are given for natural soil deposite; moist unit weight =17.8KN/m3, moisture content=1...

A: Given data: Properties of excavated soil: γ=17.8 kN/m3w=14% Properties compacted fill: γd=18.8 kN/m3...

Q: Determine the force in members CD, CJ, KJ of the truss which serves to support the deck of a bridge....

Q: Determine the factor of safety against overturning.

Q: A continuous beam is subjected to a dead load of 10 kN/m and a live load of 25 kN/m. Use NSCP 2001 p...

Q: Solve for the following internal forces occurring on the beam loaded as shown below a. Moment at B i...

A: Given- Here, a= 4.1 m, b=45.6 kN/m, c= 33.4 kN , d= 13.8 kN/m Calcula...

Q: Determine Y-bar and the Moment of Inertia about the Neurtal Axis, IN/A, and the corresponding Radius...

Q: 40 kN/m 15 KN/m 600 mm GOomm 600 mm

Q: the coordinates of the centroid of the shaded areas

A: To find the coordinates of the centroids

Q: a. Axial force on member marked with a in kN. b. Axial force on member marked with b in kN.

A: Axial Force in member a is 10.2 KN

Q: Question 1. Shape functions of three-node elements a. According to Figure 1, B. Find them separately...

A: (a) Solution: Let us consider ξ = x For figure 1 Given at node1 ξ=0, at node 3 ξ=0.5, at node2 ξ=1 ...

Q: An 8-meter long horizontal beam is supported to the left end by a fixed support and supported to the...

Q: The alkalinity of a water sample is 120 mg/1 as CaCO3. pH of the water sample is found to be 9. Conc...

Q: 1 square = 1 sq.meter %3D F1 6 kN F2 = 13 kN %3D F3 = 16 kN %3D C1 = 23.kN %3D C2 = 25 kN %3D (Input...

A: To find moment about point A

Q: The square timber used as a railroad tie carries two uniformly distributed loads, each totaling 48 k...

Q: A dam is triangular in cross-section with the upstream face vertical. Water is flushed with the top....

Q: Determine the stress produced in rod if tensile load of 3.3 N aplied on circular cross sectional are...

Q: Instructions: Draw the three basic orthographic projections of the figure. (Top View, Front View, Ri...

A: Hand made drawing are attached herewith of different views. Which will give you idea about different...

Q: Determine the allowable axial load P capacity for a rectangular column 200 mm and fixed support at b...

Q: From the frame shown, solve for the moment reaction at fixed support. (kN m) a. 490 CCW b. 530 C...

A: Given data in question UDL Span member length Point load To find out Resisting moment at point A

Q: Determine the moment of inertia of the composite area about the x- and y-axes. 6 in.- 3 in. 3 in. 2 ...

Q: Cement Mortar Plaster Lime Plaster Gypsum Plaster Gypsum Plaster High-Strength Gypsum Plaster Fibere...

A: The objectives of plastering are: To conceal defective workmanship To give smooth surface to avoid ...

Q: A car hits a tree at an estimated 38mph on a 4% downgrade. If skid marks are observed for a distance...

Q: Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a pressure o...

Q: Find shear force at P

A: INTRODUCTION: This is a simply supported beam diagram with mix loading condition of point load and u...

Q: Q3: The Different Types of Flow? Q4: what is Bernoulli equation applications?.

A: Q3 The different Types of Flow ? Q4 What is Bernoulli equation applications?

Q: An 8-meter long horizontal beam is supported to the left end by a fixed support and supported to the...

Q: 1. For the concrete beam shown, calculate the maximum tensile force (P) that can be applied to the b...

A: Given Data -

Q: 300 N/m 3 m 1.5 m Draw The Moment diagram for the beam

Q: Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section made from a T-...

Q: Determine the moment of inertia of the section (in mm4) about the horizontal neutral axis. All dimen...

Q: Wo A

Q: What document is required for facilities before they discharge treated wastewater into bodies of wat...

Q: Solve for the following internal forces occurring on the beam loaded as shown below. a. Moment at B ...

Q: Situation 1] A circular road is proposed to be laid out with tangent AB whose bearing is N8Z°54'E in...

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since th...

Q: Determine the stress produced in rod if tensile load of 3.3 N aplied on circular cross sectional are...

Q: 250 mm fe = 21 MPa fy = 415 MPa n = 9 Tension reinforcement: 2 – 25mmØ RSB 1.4 Pmin fy Pmax = 0.75Pp...

A: Moment Capacity - The moment capacity is maximum bending moment that can be resisted by an element b...

Q: Determine the design strength of the beam shown. Assume fy=345MPA and fc=21MP.. 3-22 mm 75 375 mm SL...

A: We have to determine the value of design strength of the beam shown as per the given data in the que...

Q: 2. Determine the net area of a W12X16 given a staggered bolt connection in the web in in?. Assume 1i...

Q: An unsupported excavation is made to the maximum possible depth in a pure clay soil having density 2...

Q: Sustainable Procurement has mostly been implemented by some developed countries. Mainstreaming susta...

A: Sustainable obtainment empowers public foundations to address the issues of products, administration...

Q: Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the s...

Q: The ratio of volume of voids to volume of solids is

A: Density is defined as the ratio of mass upon volume . Density is denoted by ρ . Porosity is denoted...

Q: Draw shear and moment diagram. nd max. M Draw loading and moment diagra near diagram 6. Shear diagra...

Q: Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the a...

A: To find the absolute value of maximum shear produced

Q: Determine the maximum flexural stress at 1 m from the support at D to E in MPa.

Q: A glass sphere (Rd= 2.7) 1 mm in diameter is observed to have a fall velocity of 1.25 cm/s in an oil...

A: The viscosity is a measure of the resistance of fluid to flow. It defines the friction within a movi...

Q: Soil Exercise The flexible area shown in Figure is uniformly loaded. Given that q = 300kN/m? determi...

A: Solution: Given q=300 kN/m2 Z= 3m 8 meter wide Vertical Pressure due t o a A line Load: σZ= 2qπZ=2...

Q: Arectangular concrete hollow section simply supported beam shown below have the following dimensions...

A: Maximum Bending moment of a simply supported beam with Udl at full span =wl28 StressStrain=Young's M...

Q: Link AB is to be made of steel for which the normal stress is 450 MPa. Determine the cross-sectional...

A: Given data, Normal stress = 450 MPa Angle = 35 ° Point load = 20 kN UDL = 8 kN/m To find out the cr...

Q: Draw the shear and moment diagrams for the beam

Concept explainers

Field applications of hydraulic conductivity

Hydraulic conductivity is one of the hydraulic properties of soil defined as a measurement of the ability of a porous medium to permit water movement or fluid flow through it. It is denoted by the letter K. It is influenced by the density and viscosity of the fluid. It is also called permeability. Hydraulic conductivity is defined as the ratio of velocity to the hydraulic gradient. The different methods used to determine the hydraulic conductivity are laboratory methods (constant head permeability tests and falling head tests), in-situ field methods (pumping in and pumping out tests), small scale field tests (infiltration tests and slug tests), and indirect methods such as estimation from grain size, consolidation test data, and horizontal capillary test. The pedotransfer function (PTF) method is a specific empirical estimating approach employed in the soil sciences is also used to determine the hydraulic conductivity of the soil.

Question

A sand layer of the cross-sectional area shown in the figure has been determined to exist for a 800-m length of the
levee. The hydraulic conductivity of the sand layer is 1.65 m/day.
Determine the quantity of water which flows into the ditch in m3/min.
Elv, 175 m
Levee
Elv. 130 m
2 m
Ditch
180 m
Impervious O Sand

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Field Applications of Hydraulic Conductivity

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A sand layer of the cross-sectional area shown in the figure has been determined to exist for a 500 m. length of the levee. The hydraulic conductivity of the sand layer is 3 m/day. Determine the quantity of water which flows into the ditch in cu.m/min. * O (3 Points) w.s. El.=160 Levee Impervious layer' 10 m w.s. El.=150 2 m Sand Ditch Impervious layer 125 m O 240 cu.m/min O 0.166 cu.m/min O 288 cu.m/min
Don't copy from other solutions thank you. Three piezometers have been installed in the confined aquifer having a uniform thickness of 4.6 m. and hydraulic conductivity of 2 x 104 m/s. a) Compute the hydraulic grądient. b) Compute the transmissivity in m2/day. c) Compute the flow rate per unit width of the aquifer in liters/day.
A sand layer of the cross-sectional area shown in the figure has been determined to exist for a 800-m length of the levec. The hydraulic conductivity of the sand layer is 1.65 m/day. Determine the quantity of water which flows into the ditch in m/min. Elv. 175 m Levec Elv. 130 m 2 m Ditch 180 m Impervious O Sand
Need help with C. 8. An aquifer has a hydraulic conductivity of 12 ft/d and an effective porosity of 17% and is under a hydraulic gradient of 0.0055. (A) Compute the specific discharge. (B) Compute the average linear velocity. (C) The water temperature is 14°C and the mean pore diameter is 0.33 mm. Is it permissible to use Darcy's law under these circumstances? What is the reason for your answer?
← Darcy' Law A sand sample of 35 m² cross sectional area and 20 cm long was tested in a constant head permeameter. Under a head of 60 km, the discharge was 120 ml in 6 min. The dry unit weight of sand used for the test was 1120 g. and GS = 2.68 Take Sw = 1 g/ cm³ The hydraulic conductivity (in cm/sec) is × 10-³ X
A sand sample of 35 sq. cm cross sectional area and 20 cm long was tested in a constant head permeameter. Under a head of 60 cm, the discharge was 120 ml in 6 min. The dry weight of sand used for the test was 1120 g, and Gs = 2.68 1. Determine the hydraulic conductivity in cm/sec. 2. Determine the discharge velocity in cm/sec 3. Determine the seepage velocity in cm/sec
Calculate the equivalent hydraulic conductivity for the following soil sample: 1.5 ft Water O: K-2x10* ft/sec O: K=3x10* ft/sec O: K-4x10 ft/sec : K-5x10 ft/sec Water (2) 4 layers@ 0.5 ft thick each 10 ft O 0.00035 ft/sec O 0.00031 ft/sec O 0.00003
Please answer with complete solution and Fbd. A field sample of an unconfined aquifer is packed in a test cylinder. The length and diameter of the cylinder are 60cm and 8cm, respectively. The field sample is tested for a period of 2min under a constant head difference of 18.5 cm. As a result, 50cm3 of water is collected at the outlet. Determine the hydraulic conductivity of the aquifer sample.
The soil has cross sectional area of flow of 1 ft² and a hydraulic conductivity of 1.45 x 104 ft/sec. Calculate the rate of flow. Supply 7.6 ft³/day 6.3 ft³/day 3.1 ft³/day 4.8 ft³/day 1 ft Soil 2 ft H Outflow, Q
Q-b A sand layer of the cross-sectional area shown in Fig. Q-b (page 2) has been determined to exist for a 500-m length of the levee. The hydraulic conductivity of the sand layer is 2.3 m/day. Determine the quantity of water which flows into the ditch in m³/hr.
(c) A pumping well was drilled penetrating straight into an unconfined aquifer with the thickness of 42 m. The distance of pumping well with first extraction well and second extraction well are 20 and 180 m, respectively. Meanwhile, the drawdown for the first extraction well is 4.5 m, and the second extraction well is 1.5 m. The constant pumping rate has been set at 0.09 m³/s. (i) Sketch the cross section of unconfined aquifer system and label the values. (ii) Determine hydraulic conductivity of the groundwater through the soil media when it was being pumped out and classify the type of soil according to TABLE Q1(c). (iii) Point out THREE (3) negative effects that might happen for over - pumping aquifers.
49. A pumping test was made in a sand layer extending to a depth of 16m. The initial groundwater table was located 2m below the ground surface. Observation wells were sighted at distances 4m and 9.5m from the pumping well. Using a discharge of 0.4 cubic meters per hour, a steady level is attained at the pumping well. The measured drawdowns at the two observation wells are 2m and 0.25m respectively. Determine the coefficient of permeability of the soil.