!Required informationProblem 07.021 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTSNOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.During the isothermal heat addition process of a Carnot cycle, 700 kJ of heat is added to the working fluid from a sourceat 400°C.Problem 07.021.a - Entropy change of working fluid in a heat addition processDetermine the entropy change of the working fluid. (You must provide an answer before moving on to the next part.)The entropy change of the working fluid isKJ/K.

Given data as per questionIsothermal heat addition process T=constantQ=700 kJT=400°C=400+273=673 K

oblem 07.021 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS OTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to t uring the isothermal heat addition process of a Carnot cycle, 700 kJ of heat is added to the work 400°C.

oblem 07.021 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS OTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to t uring the isothermal heat addition process of a Carnot cycle, 700 kJ of heat is added to the work 400°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Brayton cicle Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.
A machine using air ( k = 1.4, R = 53.342 ft-lb/lb-R) as the working substance operates on the Carnot cycle. At the beginning of the isothermal expansion, p1 = 300 psia, V1 = 5 cu ft, and t1 = 540 degrees F. The isothermal expansion ratio is 2 ( V2/V1 and V3/V4) and the isentropic compression ratio is 5 ( V4/V1 and V3/V2). Calculate (a) the sink (cold body) temperature, (b) the heat supplied to the cycle, (c) the heat rejected, (d) work, and (e) thermal efficiency.
Based on a gas turbine with superheat and intercooling, determine: 1) The thermal efficiency (ƞterm), in %. Use the expression ƞterm= 1 –(qL/ qH)2) How does gas turbine intercooling influence thermal efficiency?3) How and why? It is said that the gas turbine cycle with intercooling, reheating and regeneration is close to the Ericsson cycle.
Find the entropy production and determine if the cycle operates irreverisbly, reverisbly, or impossibly. A refrigeration cycle operates between the freezer compartment at 268K and the ambient air at 295K. The rate of heat transfer from the freezer compartment is 8000 kJ/h and the power input for the cycle is 3200 kJ/h. Determine the entropy production for this cycle in kJ/K·h (do not convert h to s). Enter the answer without units, but with a minus sign if applicable. This cycle operates irreversibly reversibly impossibly.
103#1. the working substance for a Carnot cycle is 8lbm of air. the volume at the beginning of isothermal expansion is 9cu ft and the pressure is 300 psia. the ratio of expansion during addition of heat is 2 and the temperature of the cold body is 90degree F. find (a)QA, (b) QR, (c) V3, (D)p3 ,(e) V4, (f) p4, (g) pm, (h) the ration of expansion during thge isenthropic process and (i) the overall ration of compression.
Pls. answer thank you! The following performance data were generated by a gas turbine having intercooling: LP compressor inlet conditions of 14.7 psia and 520’’R: LP compressor isentropic discharge temperature, 743.8 R. compressor isentropic efficiency. 78 percent; HP.compressor inlet temperature, S20 degree R: HP compressor isentropic discharge temperature, 743.8 R. HP compressor isentropic efficiency, 82%; turbine inlet temperature, 2000R; and turbine isentropic efficiency, 90%, Calculate the net cycle work Btu/lb.
Air enters the turbine of a gas turbine at 1200 kPa, 1200 K, and expands to 100 kPa in two stages. Between the stages, the air is reheated at a constant pressure of 350 kPa to 1200 K. Both turbines have same isentropic efficiency 85% Determine, in kJ per kg of air flowing (a) the work developed by each stage. (b) the heat transfer for the reheat process. (c) the increase in net work as compared to a single stage of expansion with no reheat
As a car gets older, will its compression ratio change? How about the mean effective pressure?
A 2.00 mol sample of an ideal diatomic gas is taken through a reversible cycle A → B → C → A as shown in the figure below. Process A → B is isothermal expansion. For the cycle, calculate: a) the work done by the gas, b) the heat energy added to the gas, c) the heat energy exhausted by the gas, d) the thermal efficiency, e) the change in entropy of the gas. f) Determine the efficiency of a Carnot engine operating between the same temperature extremes, R = 8.314 J/mol K Data at vertices for the above PV diagram are as follow: PA = 5.00 x 105 Pa, VA = 1.00 x 10 -2 m3, PB = 1.25 x 105 Pa, VB = 4.00 x 10 -2 m3 PC = 1.25 x 105 Pa, VC = 1.00 x 10 -2 m3
Specific Instruction: i.Drawaschematic diagramof each problem with labels of states of a substance;ii.For uniformity purposes, assign STATE 1 at the inlet of ahigh-pressure turbine.The states must be arranged in a chronologicalorder;iii.Ploteach cycle in a t-s diagramwith the states consistentto the states assignment in the schematic diagram;iv.Show a detailed solution 1.Consider a 200-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 8MPa and 400 0C and is cooled in the condenser at a pressure of 10 kPa. Determine (a) the quality of the steam at the turbine exit, and (b)themass flow rate of the steam.
A gas turbine power plant working on Brayton cycle, Explain the working principle of the cycle with physical diagram as well as P-V and T-s diagrams, and with all the required details
A gas-fired power plant operating on a Brayton cycle draws in 9.0 kg/s of atmospheric air, initially at 300 K and 100 kPa, in order to generate 1.7 MW of electricity. If the combustion chamber adds heat by burning 0.07 kg/s of fuel with a heating value of 46.1 MJ/kg, and as a result the air entering the turbine is at a temperature of 861 K, determine the back work ratio of this device to 2 decimal places. You may treat the added mass of the fuel as negligible. Take the cp of air to have a constant value of 1.005 kJ/(kg K) throughout the whole cycle, and its ratio of specific heats k can be assumed to take the value 1.4.