oil has interconnected voids through which water can flow from points of high energy to point of low energy. It is necessary for estimating the quantity of underground seepage under various hydraulic conditions. Based on that statement; (i) Briefly explain the discharge velocity of water. (ii) If discharge velocity of water through a soil is 24 cm/hr and soil porosity is 30%, determine the seepage velocity of the water

oil has interconnected voids through which water can flow from points of high energy to point of low energy. It is necessary for estimating the quantity of underground seepage under various hydraulic conditions. Based on that statement; (i) Briefly explain the discharge velocity of water. (ii) If discharge velocity of water through a soil is 24 cm/hr and soil porosity is 30%, determine the seepage velocity of the water

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter7: Permeability

Section: Chapter Questions

Problem 7.3P

See similar textbooks

Similar questions

Refer to Figure 7.24. The following data were collected during the field permeability measurement of a confined aquifer using a pumping test. Determine the hydraulic conductivity of the permeable layer. Use Eq. (7.49). Thickness of the aquifer, H = 4.5 m Piezometric level and radial distance of the first observation well: h1 = 2.9 m; r1 = 17.8 m Piezometric level and radial distance of the second observation well: h2 = 1.8 m; r2 = 8.1 m Rate of discharge from pumping, q = 0.5 m3/min
Define, compare and contrast terms saturated and unsaturated hydraulic conductivity and explain theirimportance in understanding movement of water in the ground.
Refer to Problem 8.4. Using the flow net drawn, calculate the hydraulic uplift force at the base of the hydraulic structure per meter length (measured along the axis of the structure).8.24 For the hydraulic structure shown in Figure 8.24, draw a flow net for flow through the permeable layer and calculate the seepage loss in m3/day/m.
The figure below represents a system with flow in the horizontal direction. Find the value of each pressure charge, level charge, and total charge in A, B, C, D, E, F, G, plus the real and approximate velocity of water flow plotting all of the above, given that soil porosity = 0.33 and transmittance coefficient = 0.50 cm/sec
The contaminant concentration has been detected to be 200 mg/L for the area of a site represented below. The groundwater contours are spaced at intervals of about 50 m. The average thickness of the aquifer is 5 m and the hydraulic conductivity is 1x10-2 cm/s. For each meter of length (unit length) as measured parallel to the river, what is the contaminant loading rate (i.e., C x Q) in kg/year?
b) A 30-cm well fully penetrates an unconfined aquifer of saturated depth 25 m. When a discharge of 2100 lpm was being pumped for a long time, observation wells at radial distances of 30 m and 90 m indicated drawdown of 5 and 4 m respectively. Estimate the coefficient of permeability and transmissibility of the aquifer. What is the drawdown at the pumping well?
A confined aquifer has a thickness of 85 ft. An 86-in diameter well drilled to the bottom of the aquifer, as shown in fig 3-10, if the hydraulic conductivity of the aquifer is 10 ft / day, and if water is originally 170 ft deep in the well, calculate approximately the maximum rate of flow that can be pumped from the well without dewatering any part of the aquifer. Assume 1000 ft reasonable value for the radius of influence. What will be the average velocity ( Darcy velocity ) of flow in the aquifer at a distance 20 ft from the center of the well?
Water flows through a fully confined sand aquifer with a piezometric head gradient of 0.025.(a) If the hydraulic conductivity and effective porosity of the aquifer are 1.72 m/d and 0.45, respectively, estimate the specific discharge and seepage velocity in the aquifer.(b) estimate the volumetric flow rate of the groundwater if the aquifer is 45 m deep and 1.2 km wide.(c) How long does it take a dissolved contaminant in the groundwater to move 1 km?
From the figure shows an unconfined non homogeneous aquifer between two water bodies at depth of 50 m and 45 m. respectively. Compute the average coefficient of permeability of the aquifer and the rate of flow.
The aquifers wherein the groundwater flows has a cross-sectional area of 10,000 m^2 and a length of 1,500 m. Hydraulic heads are 250 m and 300 m at the groundwater exit and entry points in the aquifer, respectively. If the groundwater discharges into a stream is at the rate of 50 m^3/month: a. What is the Darcy's velocity per day? b. Determine the hydraulic gradient? c. Determine the hydraulic conductivity per day?
The hydraulic conductivity of a homogeneous gravelly aquifer is 3 x 10-1 cm/sec. The hydraulic gradient (groundwater surface slope) of the phreatic (water table) aquifer is 0.01 and the aquifer's effective porosity is 0.25. Calculate the following two parameters and provide the answer to question b) in the space provided (numerical answer only, no units or any). Calculate the specific discharge that represents flow conditions of the aquifer in cm/sec. Also Calculate the approximate average velocity of a conservative solute dissolved in this aquifer, calculated to units of cm/sec (enter numerical answer without stating units).
2. A confined aquifer is recharged by a continuous supply of water from the certain source. The average thickness of the aquifer was determined to be 25 m and the average width is 4 km. The hydraulic conductivity of the aquifer was obtained at 40 m/day and its void ratio is 0.3333. The piezometer heads in two wells 1.325 km apart are 65 meters and 60 meters from a common reference datum. Determine the rate of flow in cubic meters per day. Determine: •compute the rate of flow through the aquifer in m3/day •compute the seepage velocity in m/day •compute the time of travel from the head of the aquifer to a point 8 km downstream in days