On what is the flexure formula based?

Q: Q.2 Is this roll bar set to full 'stiff' or full 'soft'?

A: Solution:   The correct answer with necessary explanation is given below:

Q: What is the main cause of bearing failures?

A:

Q: What are advantages of Spring usage?

A: Spring: It is a mechanical device or object which has a ability to store the mechanical energy. The…

Q: What is the Torsion formula?

A: The expression of torsion equation is given by, Here, T is the twisting torque, J is the polar…

Q: 11. A rear flange mounted cylinder extends 14 in. under a load of 10,000 Ibf. What size cylinder rod…

A: Given       Mass, m = 10000 lbf                     = 4535 kg Extension, h = 14 in…

Q: What is the force output of a cylinder that has a 1” bore and operated at 600 psig?

A:

Q: spring as alculate the true load and load force when the indic

A: given:m1=10gw1=0m2=60.3gw2=50gw3=100g

Q: An ASE automotive grade bolt with three slash marks on its head, indicates a hardness of what grade…

A:

Q: How can the average shear stress be related to the torque?

A: Let us consider an example of a cylinder rotating in viscous fluid with some average shear stress…

Q: 1. A 4-stroke, single-cylinder gasoline engine has 85-mm bore and 85-mm stroke. What is the piston…

A:

Q: Describe how torque on a solid shaft can be measured using strain gauges?

A: Strain guage converts the torque into change of electrical resistance. This guage is bonded to…

Q: xplain about different types of bearing failures on machir

A:

Q: What is the difference between kinetic and static friction. Given example of each.

A: Static friction When an amount of force act on an object, then the resisting force applied between…

Q: What is referred to as the torsion formula?

A: Let us consider a shaft subject to the torque at the free end and fixed at the other end.

Q: On a helical compression spring, the direct shear stress is greater than the torsional shear stress.

A:

Q: A higher polar moment of inertia means that the specimen needs a lower angle of twist to be failed.…

A: The angular deflection of the specimen is given by - θ=TLGIP⇒T=GIPLθwhere T= Twisting Moment ,…

Q: Find the F thrust and F frictional force using the following info

A: In trial 1, calculate the coefficient of friction. Angle,…

Q: The output shaft of a reducer is bearing in bearings A and B. From deep groove ball bearings, bed A…

A: Given that the output shaft of a reducer has bearings A and B. The bearings are deep groove ball…

Q: True/false Q-5 Specific weight is an extensive property? If yes why ?

A: Specific weight is define as tge ratio of weight of the substance to its volume.  w• = W/v  W = mg {…

Q: ving data were recorde tensile test of a 12.8 m teel rod. The gauge 5 50 mm. ress-strain diagram anc

A: Calculate the cross section area of test specimen of mild steel. A = π4 d2 Here A cross section area…

Q: What is the cause of friction?

A: Friction is a force that comes into existence when there is relative motion between two bodies, or…

Q: Statics; Method of joints Solve the following problems with accompanying complete- detailed…

A:

Q: The cylinder head of a 10”x18” refrigerant compressor is attached by 10 stud bolts made of SAE grade…

A:

Q: List four possible causes of cluth slippage

A: A Clutch is a mechanical device used in vehicles that transmits power from the motor to the…

Q: ch. The friction lining has a ce 25. The bore radius of friction li ilom contLacl pressur of IMI

A:

Q: B. what is the type of force in each one of the figures below depending on the contact? 2 00. Fpash…

A: Types of Forces acted at different Kinds.

Q: s loaded by a uniformly distributed torque of intensity stance what is the angle of twist between…

A: Given data as per questionL=Length of prismatic bard=Diameter of bart=Intensity of Uniformly…

Q: Design and explain fatigue test setup for a crankshaft ?

A: Consider the diagram shown below for the crankshaft setup, For the resonance fatigue test…

Q: Which of the following is the permissible working stress in psi of UNC bolts that has a stress area…

A: Given Data: Stress area of the bolt, A=0.4 in2

Q: change in spring stiffness is?

A: Given: If the wire diameter of a compressive helical springs is increased by 2%,We have to find then…

Q: What is the coefficient of critical damping?

A: Coefficient of critically damping is defined as the value of damping coefficient at which the…

Q: What is the cause of slipping inductile failure?

A: Causes of slipping in ductile failure are as follows

Q: What is the Axial Load?

A: The axial load is a force that acts along the centroidal or longitudinal axis of the system. If the…

Q: um gauge pressum hieh?

A: given:height h=2.5m

Q: -.3: Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer…

A: Given data: The diameter of the bolt is D = 24 mm. The length of the bolt is L = 100 mm. Here, the…

Q: what is the part of the spring being compressedor stretched upon application of force

A: When the force (tensile or compressive) is applied the spring either get elongated or gets…

Q: Which is procedure provides a method that may be used to determine the displacement of any joint on…

A: We can use the method of virtual work to determine the displacement of a truss joint when the truss…

Q: ball bearing operating at a load F has 8000 hours of life. What is the life of the bearing, in

A: Given:Load F has 8000 hours of life,

Q: CII-3. Use reasonable dimensions for this hammer and a loading to show through an analysis why this…

A: The free body diagram of the hammer is given by, Here, F is the human effort.

Q: How to solve SOLVING RIGID-BODY EQUILIBRIUM PROBLEMS?

A: The body is said to be in equilibrium when the net force and net torque acting on the body is zero.…

Q: l the spring be compressed?

A: x= 13.717cm

Q: QIDiscuss in detail the effect of the Diameter in the Buckling of hollow shaft

A: Buckling : It is a spontaneously bends from straight beam in to curved shape under an axial…

Q: Crate coef of static friction is .55, what is min force to prevent slipping, what is min force to…

A: Given Data: The coefficient of static friction is, μ=0.55. The weight of the crate is, W=1000 N.

Q: Which deformation is stay after removing of external load ?

A: Given Data⇒External LoaddeformationProblem definition⇒Problem says determine which deformation stays…

Q: With neat sketch explain six different bearing failures, causes and cures.

A: Bearing failures, causes and cures

Q: What size of hole must be drilled in an M 42 bolt to make the bolt of uniform strength

A:

Q: Based on the figure If spring A is compressed (L / 8) Which shape is correct? 1 or 2 ?

A: The center of mass of a distribution of mass in space is the unique point where the weighted…

Q: The critical speed of the shaft is

A: