P=47T= 0.69 s Shown below is a vibrating system that consists of a stepped cylinder of massm= 10 kg and radius of gyration about its center of gravity of ko = 140 mm. After aninitial disturbance, the amplitude x is found to decrease to [pl% of its initial value inone complete cycle. The period of oscillation is observed to be [7] s. Find the springconstant k and the damper constant c. The cylinder rolls without slipping.Take r= 150 mm.The specific values ofp and T are identified in a separate excel sheet.m, k.www

Answered: Image /qna-images/answer/b46902f5-08c4-4567-b192-7bd133110a92.jpg

Answered: one complete cycle. The period of…

one complete cycle. The period of oscillation is observed to be [7] s. Find the spring constant k and the damper constant c. The cylinder rolls without slipping. Tolre u 150

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A three-blade wind turbine used for research is supported on a shaft so that it is free to rotate about O. One technique to determine the centroidal mass moment of inertia of an object is to place a known weight at a known distance from the axis of rotation and to measure the frequency of oscillations after releasing it from rest with a small initial angle. In this case, a weight of Wadd = 50 lb is attached to one of the blades at a distance R = 20 ft from the axis of rotation. Knowing that when the blade with the added weight is displaced slightly from the vertical axis, and the system is found to have a period of 7.6 s, determine the centroidal mass moment of inertia of the three-blade rotor.
A single-cylinder compressor with a mass of 150 kg is mounted on rubber wedges.Compressor rubber wedgesit has been observed that the wedges collapsed by 2mm when placed on it Damped free on wedges without starting the compressorwhen released into vibration, it completed 100 full oscillations in 10 seconds. The stroke of compressor is 100mm a-)Calculate the spring constant (k) of the wedges. b-) Calculate the degree of damping (c) of the wedges. c-)The vibration amplitude of the regular regime was measured as 1mm when the compressor was operated at a speed of 1000rpm In the compressorcalculate the amount of moving masses.
An electric motor of mass 25 kg is supported on a three-spring system. Thesprings are arranged in parallel, with the three stiffnesses being 10 kN/m,5 kN/m and 25 kN/m respectively. Viscous damping is present within the systemand has a magnitude of 0.4 kNs/m.i) Produce a sketch of the system and state its equation of motion.ii) Determine the damping ratio and comment on its value.iii) Determine the amplitude of vibration of the motor 5 cycles afterit is released from an initial displacement of 15 mm.
An sdof system consists of mass 175 kg and a spring constant k 530 kn/m while testing the system a relative velocity of 0.3 m was observed on application of force of 450 n determine the damping ratio
Determine the steady-state amplitude of the mass center of the bar of Fig P6.3 when its right end is subject to a moment M=4000sin105t N.m. Expected answer X=0.988mm
A body vibrating with viscous damping makes five complete oscillations per second, and in 10 cycles its amplitude diminishes by 1/5 of the orginal value. Determine the logarithmic decrement and the damping ratio.
The mass of a single degree damped vibrating system is 7.5 kg and makes 24 free oscillations in 14 seconds when disturbed from its equilibrium position. The amplitude of vibration reduces to 0.25 of its initial value after five oscillations. Determine : 1. stiffness of the spring, 2. logarithmic decrement, and 3. damping factor, i.e. the ratio of the system damping to critical damping.
gine driving a dynamo has a mass of 180 kg and a radius of gyration of 30 mm. The shaft at the flywheel end has an effective length of 250 mm and is S0 mm diameter. The armature mass is 120 kg and its radius of gyration is 22.5 mm. The dynamo shaft is 34 mm diameter and 200 mm effective length. Calculate the position of node and frequency of torsional oscillation. G = 83 kN/mm?>.
The complete slide- back and forth motion of a single reciprocating compressor piston completes in a 2-sec period. The volume displacement of the piston though the piston cylinder is 8,902.63 in3. The stiffness of crank is said to be equal to 65.5N/m and the mass of the said piston is at 10kgs. A.)Draw out your conclusion of the vibration found during the motion of the piston through its piston cylinder.
The flywheel of a generator set weighs 150 kg and its radius of gyration is 25 cm. The diameter offlywheel shaft is 4.5 cm and length is 22 cm. The mass of armature is 90 kg and radius of gyration is 20cm. The dynamo shaft is 4 cm in diameter and 18 cm long. Determine frequency of torsional vibration.Neglect inertia of shaft and coupling. Assume G = 8.24 × 10 6 N/cm
As shown in the Fig. 3, the CM of a cylinder of mass m and radius R is connected to the top of hoop of mass m by a spring. The spring constant is assumed to be known and it is denoted by k. At a given moment the system is slightly compressed and then suddenly released. After the release, both rigid objects roll without slipping. Determine the angular frequency of the resulting oscillation. It is assumed that the spring remains horizontal throughout the motion. Figure 3: Coupled Oscillator
A 50 kg dough machine is mounted on an elastic support and opera to a speed of 1000 rpm. It has an unbalanced mass of 2 kg at an eccentric distance of 0.1 meter. If the damping factor ℶ = 0.2, determine: a) the constant of the support spring (without damping) which only transmits only up to 28% of the unbalanced force to the foundation, b) the resonant frequency in rpm, and c) the magnitude of the force transmitted with the complete suspension d) Illustrate using graphics