Design a differential amplifier such that an output of 15V is obtained when 6V and 3V are given at the non-inverting and inverting terminals respectively.i) Select the resistances accordingly and draw the circuit designing with the mentioned specifications.ii) Explain and show all calculations. 1. Design a differential amplifier such that an output of 15V is obtainedwhen 6V and 3V are given at the non-inverting and inverting terminalsrespectively.i)Select the resistances accordingly and draw the circuit designingwith the mentioned specifications.ii)Explain and show all calculations.

Answered: Image /qna-images/answer/1d6a8699-5d96-44ea-ad7c-9abecc7f2a2f.jpg

Design a differential amplifier such that an output of 15V is obtained when 6V and 3V are given at the non-inverting and inverting terminals respectively. i) Select the resistances accordingly and draw the circuit designing with the mentioned specifications. ii) Explain and show all calculations

Design a differential amplifier such that an output of 15V is obtained when 6V and 3V are given at the non-inverting and inverting terminals respectively. i) Select the resistances accordingly and draw the circuit designing with the mentioned specifications. ii) Explain and show all calculations

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Related questions

Q: A differential amplifier has a differential gain of 500 and negligible common-mode gain. The input…

Q: 8002 Q.16: Find the values of H-Param eters for the operational-amplifier shown? (Ans.: h=2000,…

A: Ohm's law: This law states that the current is directly proportional to the voltage and inversely…

Q: Op-Amp Based Circuit For the circuit given in Fig. 1, the operational amplifiers are ideal. Find…

Q: = ??? out V. +15 V Ideally, when the two input terminals of an op-amp are shorted together (creating…

Q: Draw the dc equivalent circuit and find the Q-point for the amplifier shown. Assume Kp = 400 μA/V2,…

Q: For the Differential amplifier shown:, calculate the following: 1. The differential mode gain 2.…

A: Here, we have given a differential amplifier. The values of electric current density are defined in…

Q: (A) In a 6-bit weighted resistor DAC in which the feedback resistor Rf has 4times the value of MSB…

Q: 7. Using two multipliers with attenuation factor (k) and one op-amp, design a circuit having two…

A: In this given questions we need to design the circuit according to desirable output given the the…

Q: The circuit shown can be used as a variable capacitor, where CM can be tuned by changing the…

Q: Design an amplifier circuit that gives unity gain Prove your design with suitable mathematical…

A: Unity gain amplifier can be designed with opamp

Q: 9.27 An npn differential amplifier with I = 0.4 mA, Vcc = VEE = 2.5 V, and R. = 5 k2 utilizes BJTS…

Q: Find vo in terms of vs. Assume that the op amp is in its linear region of operation. Find the…

A: The op-amp is considered to be ideal which means having infinite gain and infinite input impedance.…

Q: Is it possible to get a gain less than unity using a non-inverting amplifier configuration? If yes,…

A: A noninverting amplifier is an op-amp-based amplifier with a positive voltage gain. An op-amp is the…

Q: The op amps as shown are ideal. What are the nominal, minimum, and maximum values of the voltage…

Q: 8.10 Differential amplifiers are often used in conjunction with Wheatstone bridge circuits. Consider…

A: (a) The equivalent circuit as seen from the inverting terminal of the op-amp is,

Q: The common mode rejection ratio, CMRR of an operational amplifier is a metric used to quantify the…

Q: We can make use of a non-inverting amplifier to build a -current source. To do this, consider the…

Q: A noninverting ampliﬁer is designed to have a gain of 200 (46 dB) and is built using an operational…

A: Given data, The value of gain 1β = 200. The value of open loop gain is A= 80 dB. Converting open…

Q: If an inverting amplifier takes input supply voltage of 20V, input resistance and feedback…

A: Given: Input voltage = 20V Input resistance = Ri=15Ω Feed back resistance = Rf=60Ω

Q: I am having trouble with a Differential Amplifier problem that I attached a photo of. I must "Design…

A: For a single input single output BJT amplifier for the gain of +150 we have to make some changes in…

Q: 8002 Q.16: Find the values of H-Parameters for the operational-amplifier (op-amp) circuit I 408 1602…

A: Given circuit is -

Q: Ques. 11. Input x(t) applied to an inverting op-amp follower circuit produces output y(t) according…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: The 3-OpAmp Instrumentations Amplifier in Fig. Q.B2(a) is the front-end stage of an ECG amplifier,…

Q: we need to construct an amplifier that has value of Ad=500 and BW=80kHz. can the uA741 operational…

A: OP-AMP (operational amplifier): This is an integrated circuit. The…

Q: Operational amplifier (Op-Amp) Exercise In a certain application, produces a 1 mlme signal. This…

Q: What is the outpul voltage from a 4-bit R-2R DAC, if the feedback resistor is 10 kQ and the network…

Q: The circuit shown above uses an op amp having a ±4-mV offset. What is its output offset voltage?…

A: identify the nodes Then using the KCL obtain the equation of the output voltage for three different…

Q: a) A source vs = 2 V with internal source resistance Rs =10 kΩ applies a signal to a 5 gain…

Q: For the following circuit (Fig. A1d), assuming a value of Vs = 10 V, calculate the values of VI, VN…

Q: (b) The 3-OpAmp Instrumentations Amplifier in Fig. Q.B2(a) is the front-end stage of an ECG…

Q: Design an inverting circuit using a single operational amplifier that produces an output, vo =-(8V1…

Q: (a) Design a single-stage inverting ampliﬁer with a gain of 46 dB using an operational ampliﬁer. The…

A: According to question this is the diagram of the inverting amplifier, a) i0=iL+i2 =vsRLBut,…

Q: 8002 Q.16: Find the values of H-Parameters for the operational-amplifier shown? (op-amp) circuit I…

Q: Question1 You have a sensor R₂ and a Wheatstone bridge connected to an instrumentation amplifier…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: Suppose that an op amp has a slew rate of 0.5 V/μs. What is the largest sinusoidal signal amplitude…

A: According to question: Largest sinusoidal that can be produced at a frequency of 20kHz is…

Q: 3. Using two multipliers with attenuation factor (k) and one op-amp, design a circuit having two…

A: Since you have posted the multiple questions so we are supposed to answer the 1st questions. 3) In…

Q: Using inverting, non-inverting, Buffer, or Summer op_amps circuit to design the following equation…

A: We can achieve the function as follows using a non-inverting amplifer.

Q: What is the maximum peak-to-peak output voltage for a 741 op-amp with ±15 V power supplies? How…

A: Supply voltage of 741 op-amp is Here, maximum output voltage of op-amp is limited by the saturation…

Q: The op-amp circuit to the right is a non- R3 V3 inverting summing amplifier. First, find V as out R2…

Q: What is the CMRR of the op-amp in dB if the open-loop differential voltage gain of 200,000 and a…

A: We need to find out comman mode rejection ratio for opamp

Q: For the Differential amplifier shown:, calculate the following: 1. The differential mode gain 2.…

A: The answer as given below:

Q: For the circuit shown below, assume ideal op-amp, (a) Derive the expression for the output voltage…

A: From Figure V01 0= -R2R1 v1 ⇒V01= -R3R1 V01 - R3R1 V2V0 = R2R3R12 V1 - R3R1 V2 ........1

Q: 2. A sensor gives output in the range 20.0 to 250 mV as the process variable varies over its range.…

A: Op-amp- An op-amp is a very high gain DC amplifier designed to provide low input voltage offset…

Q: 8.21 Differential amplifiers are often used in conjunction with the Wheatstone bridge. Consider the…

A: (a) Short-circuit the input voltage and draw the circuit diagram to find the Thevenin resistance…

Q: For the circuit as shown, find:- A. Output at (V₁ = V₂ = 1volt)? B. Output at (V₁ = -V₂ = 1volt)? C.…

Q: 2.16: Find the values of H-Parameters for 8000 www 1602 www 16.2V, the operational-amplifier…

A: The hybrid model of the given circuit can be modeled as below. Where V1 and I1 are the input…

Concept explainers

Differential amplifier

There are two amplifying stages with common degeneration in a differential amplifier.

Question

100%

Design a differential amplifier such that an output of 15V is obtained when 6V and 3V are given at the non-inverting and inverting terminals respectively.

i) Select the resistances accordingly and draw the circuit designing with the mentioned specifications.

ii) Explain and show all calculations.

1. Design a differential amplifier such that an output of 15V is obtained
when 6V and 3V are given at the non-inverting and inverting terminals
respectively.
i)
Select the resistances accordingly and draw the circuit designing
with the mentioned specifications.
ii)
Explain and show all calculations.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I am having trouble with a Differential Amplifier problem that I attached a photo of. I must "Design a single-input, single-output BJT amplifier with a gain of -150. (Based on figure 8.4). Choose values for V sub CC, V sub EE, I sub C and R sub C. Also suggest a simple modification to the circuit that will yield a positive +150 gain." Please provide clear explanation of the logic behind the steps of your solution so I can have a comprehensive understanding.
For the circuit shown below, if the differential gain (?? ) of the op-amp is (50000) and the CMRR in (db) is (34). Find the output voltage (v_out).
The amplifier as shown has R2 = 68 kΩ and R1 = 2.7 kΩ. What are the valuesof Av A, Av B, Av C, RinA, RinB, RinC, and RoutA, RoutB, RoutC, for the amplifier equivalent circuit as shown.
Please answer asap,thank you. The input of this is an AC signal with an amplitude greater than 3 and maximum frequency of 8khz(coming from an amplifier connected to this circuit). I am using this as a voltage follower. this CC amplifier sees the 5k resistor (from an amplifier buffer). Please design this CC amplifier such that the voltage swing is maximum. What values should i use for c1 and c2? Please explain the steps in detail.
(a) A non-inverting amplifier is implemented with two 10 kΩ resistors with 5% toleranceWhat is the range of possible values for gain A? (b) Repeat for an inverting amplifier.Present theoretical calculations and confirm results in simulator (multisim, proteus).
From these data in Table, compute the gains Ad and Acm and verify that they are as designed. (Q2) From these calculations, what is the CMRR of this amplifier? (Q3) Is your differential amplifier working well?
(a) Design a single-stage inverting ampliﬁer with a gain of 46 dB using an operational ampliﬁer. The input resistance should be as low as possible while achieving the op amp output drive capability mentioned here. The ampliﬁer must be able to produce the signal vo = (10sin1000t) V at its output when an external load resistance RL ≥ 5k Ω is connected to the output of the ampliﬁer. You have an operational ampliﬁer available whose output is guaranteed to deliver ±10 V into a 4-kΩ load resistance. Otherwise, the ampliﬁer is ideal. (b) If the ampliﬁer input signal is vi = V sin1000t, what is the largest acceptable value for the input signal amplitude V? (c) What is the input resistance of your ampliﬁer?
Suppose a differential amplifier has A = 120 dB,and it is operating in a circuit with an open-circuitoutput voltage vo = 15 V. What is the input voltagevid? How large must the voltage gain be forvid ≤ 1 V? What is the input current i+ ifRid = 1 M ?
A differential amplifier has a differential gain of 500 and negligible common-mode gain. The input terminals are tied to ground through 1-kΩ resistors having tolerances of ±5 percent. What are the extreme values of the output voltage caused by a bias current of 100 nA? What is the output voltage if the resistors are exactly equal?
A differential amplifier is connected to a supply of Vs = ±10V, and has a nominal gain of 4x105. What is the maximum amplitude of the input differential voltage for the amplifier to work in linear region, i.e. for the output to remain undistorted? Write your answer in standard scientific notation in "e" format. General formulation of the standard scientific notation is: a × 10b , where 1 ≤ a < 10. E format shows that as "aeb". For example, for 2.3 * 105 write 2.3 e5 , or for 1.7*10-3 write 1.7e-3.
For the circuit shown, determine the range (i.e., maximum and minimum values) of V1 such that the op-amp operates in the linear region. Assume that R1 = 9.4 kΩ , R2 = 1.6 kΩ , R3 = 4.0 kΩ, RF = 200 kΩ, V2 = 40 mV, V3 = 100 m, and Vcc = 5 V.
To have a complete design, you are required to supply the constant current source, IQ, using the basic current mirror. You are wanted to:- a)Sketch the differential amplifier circuit together with the basic current mirror as supply current. b)Prepare your answer to the labeled circuit.