select one only. thanks! | Design a compound, spur gear train for a ratio of 120:1 and diametral pitch of 5.Specify pitch diameters and numbers of teeth. Sketch the train to scale.2 Design a compound, spur gear train for a ratio of -250:1 and diametral pitch of 9.Specify pitch diameters and numbers of teeth. Sketch the train to scale.7 Design a compound, reverted, spur gear train for a ratio of 28:1 and diametral pitch of8. Specify pitch diameters and numbers of teeth. Sketch the train to scale.Design a compound, reverted, spur gear train for a ratio of 40:1 and diametral pitch of8. Specify pitch diameters and numbers of teeth. Sketch the train to scale.5 Design a compound, reverted, spur gear train for a ratio of 65:1 and diametral pitch of8. Specify pitch diameters and numbers of teeth. Sketch the train to scale.Design a compound, reverted, spur gear train for a ratio of 7:1 and diametral pitch of 4.´Specify pitch diameters and numbers of teeth. Sketch the train to scale.z Design a compound, reverted, spur gear train for a ratio of 12:1 and diametral pitch ofI 6. Specify pitch diameters and numbers of teeth. Sketch the train to scale.

Answered: Image /qna-images/answer/8d7ebd8c-35c7-4123-9604-2216cc24e8a2.jpg

Answered: | Design a compound, spur gear train…

| Design a compound, spur gear train for a ratio of 120:1 and diametral pitch of 5. Specify pitch diameters and numbers of teeth. Sketch the train to scale.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a gear train where the input shaft rotates exactly at 4000 rpm. The output speed must be exactly 20 rpm. Use 200, full depth, involute teeth, no fewer than 17 teeth and no more than 150 teeth in any gear. Use Factoring Approach.
For the gear train below, th numbers of teeth for individual gears are 12 9gear #1), Gear 18 (gear #2), 14 (gear #3), and 18(gear #4), To obtain a counter-clockwise rotation of 1500 rpm for the output gear(#4). What should be the rotation speed of the input gear (#1) and in which directions should the input gear rotate
Using the most compact design without gear tooth interference, determine the number of teeth and stages to produce a speed reduction of 42:1. Sketch the train and label each gear and its number of teeth. Assume a 25° pressure angle, full tooth.
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise.a) By calculating gear sizes; Draw in 1:1 scale.
Design a reverted compound gear train with an exact train ratio of 75:1 and a diametral pitch of 12. Specify pitch diameters and number of teeth.
The following data relate to two meshing gears: Velocity ratio =1:3;Module: 4mm; Pressure Angle: 20°; Center distance: 200 mm Determine the number of teeth and the base circle radius of the gear wheel.
A 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressure angle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate the addendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. If the center distance is increased by 0.125 in., what are the new values for the contact ratio and the pressure angle?
Example:Design a compound gear train for an exact reduction ratio of 180:1 given: ϕ =20o Module: 4mm
Two straight-toothed bevel gears mesh with a shaft angle of 90° and a diametral pitch of 5. The pinion has 20 teeth, and the gear ratio is 2:1. The addendum and dedendum are the same as for 20 stub teeth. For the gear, determine the pitch radius, cone angle, outside diameter, cone distance, and face width.
Solve this problem in spur gearsA 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressureangle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate theaddendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. Ifthe center distance isincreased by 0.125 in., what are the new valuesfor thecontact ratio and thepressureangle with complete solution and write in hand writing thank you
Consider a compound gear train to be designed for an exact velocity ratio of 90. The most acceptable velocity ratios per stage are ?
Question 01: Design a two-stage compound spur gear train for an overall ratio of approximately 17+12 : 1. Specify tooth numbers for each gear in the train.