A worm gear has 52 teeth and a diametral pitch of 6. It mates with a triple-threaded worm that rotates at 1750 rpm.The pitch diameter of the worm is 2.000 in. Compute the circular pitch, the axial pitch, the lead, the lead angle, thepitch diameter of the worm gear, the center distance, the velocity ratio,and the rotational speed of the worm gear.

Answered: Image /qna-images/answer/78a71954-ed14-44c2-828f-dbb8fb9d4773.jpg

A worm gear has 52 teeth and a diametral pitch of 6. It mates with a triple-threaded worm that rotates at 1750 rpm. The pitch diameter of the worm is 2.000 in. Compute the circular pitch, the axia pitch, the lead, the lead angle, the pitch diameter of the worm gear, the center distance, the velocity ratio, and the rotational speed of the worm gear.

A worm gear has 52 teeth and a diametral pitch of 6. It mates with a triple-threaded worm that rotates at 1750 rpm. The pitch diameter of the worm is 2.000 in. Compute the circular pitch, the axia pitch, the lead, the lead angle, the pitch diameter of the worm gear, the center distance, the velocity ratio, and the rotational speed of the worm gear.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A worm gear has 52 teeth and a diametral pitch of 6. It mates with a triple threaded worm that rotates at 1750 rpm. The pitch diameter of the worm is 50 mm. a) Compute the circular pitch, b) The axial pitch, c) The lead and the lead angle, d) The pitch diameter of the worm gear,
Two straight-toothed bevel gears mesh with a shaft angle of 90° and a diametral pitch of 5. The pinion has 20 teeth, and the gear ratio is 2:1. The addendum and dedendum are the same as for 20 stub teeth. For the gear, determine the pitch radius, cone angle, outside diameter, cone distance, and face width.
Solve this problem in spur gearsA 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressureangle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate theaddendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. Ifthe center distance isincreased by 0.125 in., what are the new valuesfor thecontact ratio and thepressureangle with complete solution and write in hand writing thank you
Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
Two spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be approximatively 200mm, calculate the following:o Pitch circle diameter of the gear;o Pitch circle diameter of the pinion;
Two spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be approximatively 200mm, calculate the following:o Circular pitch value;o Number of teeth on the wheel (gear);o Number of teeth of the pinion;o Pitch circle diameter of the gear;o Pitch circle diameter of the pinion;
A pair of gear/pinion of 42 tooth and 18 tooth with a diametral pitch of 0.7874 teeth/cm and the addendum is 0.8/p and dedendum 1/p. The gear pressure angle is 200 . Compute the center distance of the pair of gears in meters.
A two-start worm gear that is rotating at 800 rpm drives a 26-tooth worm gear. The worm gear has a pitch diameter of [46] mm and a pitch of [14] mm. If coefficient offriction (u) is 0.06, (i) Determine the helix angle of worm gear. (ii) Determine the speed of gear. (iii) Compute the distance of gear. (iv) Identify the maximum gear efficiency of this transmission system
In a spiral gear drive connecting two shafts, the approximate centre distance is 400 mm and the speed ratio =3. The angle between the two shafts is 50 and the normal pitch is 18 mm. The spiral angle for the driving and driven wheels are equal. Calculate the number of teeth on each gear wheel.
(b)A pair of straight bevel gears has a velocity ratio of 2:1. The pitch circle diameter of the pinion is 80 mm at the large end of the tooth.A5KW power is supplied to the pinion which rotates at 800 rp.m. The face width is 40 mm and the pressure angle is 20. Calculate the tangential ,radial and axial components of the resultant tooth force acting on the pinion
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate The magnitude of the velocity of slip of gears in mesh.
A similar pair of helical gears , also on parallel axes, are to have involute teeth, of 20o normal pressure angle, and 3 mm normal module. The wheels are to have 26 and 34 teeth, and to work with a centre distance of 146 mm. Calculate the transverse pressure angle in degrees.