ori (P=880 kJ /m³ ) Flow under head30 min Pr Pe (L= 3000 m , D= o-3 m) beconseOF Cooling Viscosity a long the PiPo lengthWill Chanje and equal to o.s Pa-s forISoo m and . 14Pa.s for the Yemain lengthof Pipe Prove that the flow is laminar andfind the f low ra te .

In a pipe, the critical Reynolds number:The generally recognised transition Red,crit = 2300 is the…

or1 (P-880 k9 /m³ ) Flow under hea d 3o min PrPe (L= 3000 m, D= 0-3 m) be Canse oF Cooling Viscosity a long the PiPo length Will Chanfe and equal to 0.s Pa-s for ISoo m and . 14 Pa.s for Fhe remain lengt of PiPe PYOVE that the Flow is laminar an. find the f low ra te . %3D

or1 (P-880 k9 /m³ ) Flow under hea d 3o min PrPe (L= 3000 m, D= 0-3 m) be Canse oF Cooling Viscosity a long the PiPo length Will Chanfe and equal to 0.s Pa-s for ISoo m and . 14 Pa.s for Fhe remain lengt of PiPe PYOVE that the Flow is laminar an. find the f low ra te . %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The velocity of flow of water at the centre of tube is _______ when the head is 0.1m, η=8.9*10-3 dynes-s/cm2, γw=1 g/cm3, the length is 10m and the diameter is 20cm.Dont attempt wrong I will dislike
Water flows at 20°C through a new cast iron pipe at a velocity of 4.2 m/s. The pipe is 400 m long and hasa diameter of 150 mm. Determine the head loss due to friction. Ans. 54.20 m (show the complete solution) Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet. E.g. (density, viscosity)Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness
is friction factor inversely proportional to the Reynold’s number in case of laminar flow in circular pipes?
Water (ρ=998 kg/m³, μ=1.02x10^-3 kg/ms) flows through a 598 m length of pipe with 150 mm in diameter at 60 L/s. Determine the pipe roughness, ɛ if the head loss is 49 m.
An oil is being pumped inside a pipe at rate of 5.2m/s-00. The oil density is 905 kg/m3 and the viscosity is 3.4x 10- 2 Pa' s . which pipe diameter should be used to maintain laminar flow le re <_ 2100
Find the minimum diameter of a smooth tube to ensure the flow of water at an average velocity of 100 cm/s remains turbulent. Use vwater = 1E-6 m2 /s. [Ans.: 4 mm]
Determine the Reynold's Number and flow regime of an bil flowing through a 450-mm diameter pipe, if the flow rate is 0.40 m³/s. Note: Hoil = 0.025 Pa's and Scoil = 0.86).
As a test to determine the effective wall roughness of an existing pipe installation, water at 10°C is pumped through it at the rate of 300 L/min. The pipe is standard steel tubing, 40 mm OD x 3.0 mm wall. Pressure gages located at 25 m apart in a horizontal nm of the pipe read 1235 kPa and 849 kPa. Determine the effective pipe wall roughness.
Glycerin at 40°C is flowing through a 4-cm-diameter horizontal smooth pipewith a flow rate of 6 kg/s.Determine the head loss per 10 m of the pipe.
A centrifugal pump is used to pump the water at its temperature in a reservoir with the free water surface located 2 m above the center of the pump inlet to the atmosphere. Piping system in 5ng from tank to pump; It consists of 3 galvanized iron pipes with an internal diameter of 20 cm and an average internal roughness of 0.15 mm. Local ancillary elements above the piping system are years; Sharp edged inlet (Kg-0,85), flanged smooth 3 pieces 90 ° bend -0,3 each thousand and one flanged full open globe valve (KK-8). Find the net positive charge on the usable suction since the minimum volumetric flow is 30 L / s that can be mpaed without cavitation. Evaporation pressure for water at 25 ° temperature: 3.169 kPa) (Standard atmospheric pressure: 101.3 kPa) -997 kg / m3 (-1.05) (dynamic viscosity of water at 25 ° temperature: 8.91.10-kg / ms)
In a water Transfer installation, from the storage tank to the consumption tank, a pump is to be installed to circulate a flow rate of 60 lt/s. The 380 meter long Pipe is Made of cast iron of 150 mm diameter and consist of a check valve, a gate valve and 3 commercial elbows of medium Radius.The consumir tank is pressurized to 3.5 Kgf/cm2 gauge pressure.Determine the driving power of the KW pump if it's efficiency is 73%. Additional data, head loss factors: - check valve - Open gate valve Kv= 0,19 -commercial elbow of average Radius Kc= 0,75, per elbow. - storage pond outlet sharp angles Ks = 0,5 - inlet to consumption pond Le = 1 - Pipe friction factor f = 0,029
plzzzz help me with this one plzzz Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m3 ) is to be pumped through 50 m of pipe from lower reservoir to a higher reservoir at a rate of 0.2 m3/s. If the pipe is cast iron of diameter 12 cm and the pump efficient is =0.44%, the major head loss inside the pipe is ¼ of the velocity head what horsepower pump is needed? Hint: consider the abrupt expansion only as a minor loss.