|2000 lbf d = 1.25 inch speed = 2200 rpm Shaft load = 2000 lbf (centered between bearings) Temperature: 170 F Bearing specs: O, = 25 Length ratio= 0.80 Tr clearance ratio: Cd - 0.002 2. Hydrodynamic bearings are to be selected for the design shown above. Find the following: eccentricity ratio e , eccentricity e, in., hmin in., Pavs. Ibf/in, Torsional resistance T, in-lbf, Viscosity n. microreyn, Oil type: SAE , power loss o HP

|2000 lbf d = 1.25 inch speed = 2200 rpm Shaft load = 2000 lbf (centered between bearings) Temperature: 170 F Bearing specs: O, = 25 Length ratio= 0.80 Tr clearance ratio: Cd - 0.002 2. Hydrodynamic bearings are to be selected for the design shown above. Find the following: eccentricity ratio e , eccentricity e, in., hmin in., Pavs. Ibf/in, Torsional resistance T, in-lbf, Viscosity n. microreyn, Oil type: SAE , power loss o HP

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A device contains two bearings is to operate at 300 rev/min, 8 hours per day, 5 days per week for 5 years with a reliability of 0.99. The design load is (2000+N) N and an application factor of 1.2 is appropriate. Find the catalog rating C10 For ball bearings For roller bearings The Weibull parameters are and Use SI units. Take the relations as and Where the subscripts D: desired R: rating f: factor
A 02-series single-row deep-groove ball bearing is to be selected from Table 11–2 for the application conditions specified in the table. Assume Table 11–1 is applicable if needed. The value of radial load Fr = 8 kN, axial load Fa = 2 kN, design life LD = 2.40(108), ring rotation factor V = 1, and reliability RD = 0.98. Assuming that the values taken from Table 11–1 are X = 0.56 and Y = 1.63, determine the equivalent radial load rating for this application. What is the equivalent radial load rating for this application in kN?
A certain application requires a ball bearing with the inner ring rotating, with a design life of 26 kh at a speed of 455 rev/min. The radial load is 2.5 kN and an application factor of 1.2 is appropriate. The reliability goal is 0.92. Find the multiple of rating life required, xD , and the catalog rating C10 with which to enter a bearing table. Choose a 02-series deep-groove ball bearing from Table 11–2 and estimate the reliability in use.
i) Explain the static rating of rolling contact bearings. ii) Write any three technical reasons why ball and roller bearings need to be lubricated. b) Design a self-aligning ball bearing to be used in a turbine to carry a combined radial load of 4466 N and thrust load of 1420 N. The basic dynamic load rating of the bearing is 31 kN at 547 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.3. The axial and radial load factors are 1.8 and 1.2 respectively and the rotational factor is 1. Calculate: i) Basic equivalent dynamic load in N ii) Design equivalent dynamic load in N iii) Expected life of bearings in hours
b) Design a single row deep groove ball bearing with basic dynamic load rating of 33 KN to be used in a turbine to carry a radial load of 1584 N. The expected life of the bearing is 5591 hours at 529 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in N
It has a full-slide type bearing rotating at a speed of 1975 rpm.A load of 5693 N is applied. SAE 40 oil in bearing at 60C inlet temperatureplanned to be used.Shaft and bushing diameters in bearing with tolerance data 41−0.010 respectively+0.000mmand 41.125−0.000+0.100 mm.Average radial clearance mounting for this bearing with bush length 20.50 mmCalculate the following;a) Bearing characteristic number,b) Minimum lubricant film thickness,c) Eccentricity value,d) coefficient of friction,e) Average oil film temperature andf) Find the Tmax temperature value.
pleassssse solve question 8, statics
An overhung countershaft is supported by rolling contact ball bearing. The shaft speed is 790 r.p.m. The bearings are to have 94% reliability corresponding to a life of 26000 hours. Compute and choose the value of nearest rating life L90. a. 4.9x109 rev. b. 8.6x109 rev. c. 1.9x109 rev. d. 6.2x109 rev.
A single row deep groove ball bearing is operating at a speed of 2000rpm acted upon by a radial load of 10kn and thrust load of 8kn. The bearing is subjected to light shock load and outer ring is rotating. Determine the life rating of the bearing
A ball bearing subjected to a radial load of 4000 N is expected to have a satisfactory life of 12 000 hours at 720 r.p.m. with a reliability of 95%. Calculate the dynamic load carrying capacity of the bearing, so that it can be selected from manufacturer's catalogue based on 90% reliability. If there are four such bearings each with a reliability of 95% in a system, what is the reliability of the complete system?
a steam engine runs at 150rpm. its turning moment diagram gave the areas in mm2 taken in order above and below the mean torque line is 500,250,270,390,190,340,270,250, the scale for turning moment is 1mm=500mnm, 1mm=5’ if the fluctuation of speed is not to exceed +or-1.5% of mean, determine a suitable diameter and cross-section of the rim of flywheel with axial dimension equal to 1.5times the radial dimension. the hoop stress is limited to 3mpa and the density of material of flywheel is 7500kg/m3.
b) Design a self-aligning ball bearing with basic dynamic load rating of 69.5 KN to be used in the automobile industry to carry a thrust load of 1184 N. The expected life of the bearing is 5201 hours at 628 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.7 and radial and axial load factors are 1.4 and 2.2 respectively, the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Radial load acting on the bearing in N