On the circuit board in figure below, what happens if the middle lead (wiper) of the 100k potentiometer is broken? öslg äbäi On the circuit board in figurebelow, what happens if themiddle lead (wiper) of the100k potentiometer is* ?brokenVR1Broken wire100K+12V4INPUTR2IC 110KR3741OUTPUT10K--12VThe circuit will be a unity- gainamplifierThe circuit will be an infinite gainamplifierThe circuit will be a zero gainamplifierThe circuit will be a fixed gainamplifier

Answered: Image /qna-images/answer/6e125938-b0a5-4eeb-a536-c8beb93871b4.jpg

ösaly äbäi On the circuit board in figure below, what happens if the middle lead (wiper) of the 100k potentiometer is * ?broken VRI Broken wire 100K +12V4 INPUT R2 IC 1 741 10K R3 OUTPUT 10K -12V The circuit will be a unity- gain amplifier The circuit will be an infinite gain amplifier The circuit will be a zero gain amplifier The circuit will be a fixed gain amplifier

ösaly äbäi On the circuit board in figure below, what happens if the middle lead (wiper) of the 100k potentiometer is * ?broken VRI Broken wire 100K +12V4 INPUT R2 IC 1 741 10K R3 OUTPUT 10K -12V The circuit will be a unity- gain amplifier The circuit will be an infinite gain amplifier The circuit will be a zero gain amplifier The circuit will be a fixed gain amplifier

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 12PP: In an R-L parallel circuit, ET=480 volts, R=16, and XL=24. Find PF.

See similar textbooks

Similar questions

In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR
In an R-L parallel circuit, ET=480 volts, R=16, and XL=24. Find PF.
proof the equation 10.8 which represents the gain of inversting amplifer ... the proof is already exist in page 621 but there are some expressions were missed before the equation 10.7, you should start this proof from the begining and adding that missed expressions.
Derive the Vout of the circuit shown in Figure 3 below in terms of V1, V2, R1and Rf. States all your assumptions. (Show steps by steps)
Given this thevenin equivalent circuit, we now plug up a load resistor that is 500 ohms. How would you calculate output voltage and output current given this load resistor?
Figure Q. 3(b) shows an op amp circuit for linear amplifier application. (i) Determine the value of current I3.(ii) Find the value of R if the output current, Io is given as 2 mA.(iii) Explain what will happen to output voltages, V01 and V02 if the supplyvoltages, +VCC and -VCC are connected to +10V and -10V.
Design an op amp circuit to perform the following operation: vo = 3.5v1 - 2.5v2. All resistance must be < = 100k. The power supply should be +15V and -15V. Let v1 = 2V and v2 = 1V.
Subject: Circuit INote:Support the problems with circuit diagram and label the pertinent partsWith full solutions please
Q1) find for given circuit below. 1.a. What circuit is shown on the image above and what is gain ? 1.b. If R2 is 40x higher than R1 what will happen to node 2? Provide waveform and explain why it happens. 1.c. Modify the circuit to have an overall gain of 2. Provide photos
Virtual Lab: circuits and Kirchoff’s rules Go to: https://phet.colorado.edu/it/simulation/circuit-construction-kit-dc-virtual-labBuild each of the circuits in the figures, with the designed characteristics.For each of the circuits, show the calculations to find the current and the potential difference in eachelement of the circuit.In building the circuit in Figure 1) through the simulator, adjust the small resistance of the battery tozero and put in series a small resistance as required from the design.For instance, for E1 you will need abattery with V = 6V and you will need to put in series a small resistance of 0.5 Ω to simulate the smallresistance in a battery.Figure 1)Figure 2)
HELP a:Write the equation Vo according to the block diagram given below. b: Design the circuit that will perform the operation by using 0.5 V and 10 V direct current (DC) sources with a single OPAMP.
Subject: Circuits INote:Support the problems with circuit diagram and label the pertinent parts and also complete solution so that i can learn too