= ??? out V. +15 V Ideally, when the two input terminals of an op-amp are shorted together (creating a condition of zerc differential voltage), and those two inputs are connected directly to ground (creating a condition of zero common-mode voltage), what should this op-amp's output voltage be? In reality, the output voltage of an op-amp under these conditions is not the same as what would be ideally predicted. Identify the fundamental problem in real op-amps, and also identify the best solution.

= ??? out V. +15 V Ideally, when the two input terminals of an op-amp are shorted together (creating a condition of zerc differential voltage), and those two inputs are connected directly to ground (creating a condition of zero common-mode voltage), what should this op-amp's output voltage be? In reality, the output voltage of an op-amp under these conditions is not the same as what would be ideally predicted. Identify the fundamental problem in real op-amps, and also identify the best solution.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Based on the simulation’s results, explain the function of a differential amplifier. (Hints: comment on the shape of Vo1 and Vo2, explain what would happen if V1 and V2 were the same, reflect on why it is important that an ideal op-amp has infinite input impedance).
Derive the appropriate equation for an inverting amplifier with op-amp and provide the values of resistances to obtain the gain equal 3 (kvR -> infinity, Vr -> 0)
Design and draw an inverting op amp with gain -10V/V . What is the input resistance of this op-amp?
For Va = 250 mV, if the circuit given below is analyzed using the detailed model of an op amp (as opposed to the ideal op-amp model), calculate the value of open-loop gain A required to achieve a closed-loop gain within 2 percent of its ideal value. Assume zero output resistance and infinite input resistance for the 250-Ω resistor.
An almost ideal op amp has an open-circuit outputvoltage vo = 10 V and a gain A = 106 dB. What isthe input voltage vid? How large must the voltagegain be to make vid ≤ 1 V?
Describe the respective frequency responses of inverting and non-inverting Op Amps
Question 7 For an op-amp amplifier circuit has a closed-loop voltagegain of 5. If the op-amp used has a gain-bandwidth productof 1.5 MHz, and we can only tolerate 10% drop in gain, whatwill be the maximum usable frequency? (help me do this question with explanation)
Assume that the ideal op amp in the circuit seen is operating in its linear region, What happens if R1→∞ and R2→0?
For the circuit shown above, find the gain (vo / vi). Make simplifying assumptions about the OP-AMP such as v+= v- but you must state the conditions for which this is true. Please as soon as possible！
In this Differential Op Amp, what formulas should I use to find R1, R3, and Rp when V1, V2, and Vout are already given?
Suppose the op amp shown has an fT of 3 MHz. What is the phase margin of the ampliﬁer?
Consider the active circuit with the schematic:a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem. c. If L = 1H, sketch the straight-line approximation of the Bode plot for the circuit’s gain assuming the op amp can still be considered as ideal.d. The op amp you select turns out to be non-ideal, and it has a real pole at wC = 1krad/s. Write the updated transfer function for your circuit (using your values of R1, R2, and L = 1H). Make it in the canonical form.e. Sketch the straight-line approximation of the Bode plot for the circuit with your updated transfer function from D.