Oxygen transfer medium is flowing over large semi-permeablemembranes in a blood oxygenator. The membranes are rectangularwith dimensions of 2 cm x 10 cm. The flow is along the 2 cmdimension. You can assume the viscosity and density of the medium issimilar to that of blood plasma.a) If the velocity of the fluid is 100cm/min, is the flow laminar?b) What is the thickness of the boundary layer halfway across themembrane?c) What is the value of the average friction factor on the membrane?d) How much drag force is the membrane experiencing?

Answered: Image /qna-images/answer/672c18b9-370b-48bc-8db1-f36c78484f0b.jpg

Answered: Oxygen trans aium is flowing over large…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3
In the gap between the two plates, the lubricant flows in one direction (x) by the pressure gradient. Lubricants are incompressible Newtonian fluids, flows are laminates, and terminal effects are ignored. Find the maximum flow rate [m/s] when the pressure difference (△P/L) per unit length is 25000 Pa/m.Data: clearance between plates (B) = 6 mm, lubricant viscosity (μ) = 25 cP (1cP = 10-3 Pa·s), lubricant density (=) = 0.88 g/cm3 Please.. explain more easy
Liquid is pushed through the narrow gap formed between two glass plates. Thedistance between the plates is h and the width of the plate is b . Assuming that theflow is laminar, two-dimensional and fully developed, derive a formula for thelongitudinal pressure gradient in terms of the volumetric flow rate, Q, the fluid viscosityand the distances b and h .In an example the above conditions apply with b = 0.10 m and h = 0.00076 m. Theliquid is glycerine that has an absolute viscosity of 0.96 N s/m². A pressure differenceof 192 kN/m² is applied over a distance of 0.24 m. Calculate the maximum velocity thatoccurs in the centre plane of the gap and the mean velocity.Answer 0.06 m/s
The flow rate of water in a garden hose is measured using the bucket-andstopwatch method. Filling a 5-L bucket takes 75 seconds. If the inner diameter of the hose is 10 mm and the density and viscosity of water are approximately 998 kg m-3 and 0.9 cP, respectively, (a) is the flow inside the hose laminar or turbulent? (b) If the flow rate is adjusted such that the flow is with Re = 2100, how long would it take to fill the same bucket?
Cell culture media is flowing through a cylindrical tube at a volumetric flow rate of 12 ml/s. The tube has a diameter of 0.8 cm and length of 12cm. Assume the viscosity of the media is 1.2 cP (0.0012 Pa s). a. What is the shear rate at the wall of the tube ? b. What is the shear rate at the centerline of the tube ? c. What is the shear stress at the wall of the tube ?
An important parameter in fluid flow problems involving thin films is the Weber number (We) which can be expressed in equation form as We=[pv^2L/(omega)] where p is the density of the fluid, v is a velocity, L is a length, and (omega) is the surface tension of the fluid. If the Weber number is dimensionless, what are the dimensions of the surface tension (omega)?
Professor Seymour Fluids uses a small closed-loop water tunnel to perform flow visualization research. He would like to double the water speed in the test section of the tunnel and realizes that the least expensive way to do this is to double the rotational speed of the flow pump. What he doesn’t realize is how much more powerful the new electric motor will need to be! If Professor Fluids doubles the flow speed, by approximately what factor will the motor power need to be increased?
Under laminar conditions, the volume flow Q through asmall triangular-section pore of side length b and length Lis a function of viscosity μ , pressure drop per unit length∆p / L , and b . Using the pi theorem, rewrite this relation indimensionless form. How does the volume flow change ifthe pore size b is doubled?
A water pump increases the pressure of the water passing through it. The flow is assumed to be incompressible. For each of the three cases listed below, how does average water speed change across the pump? In particular, is Vout less than, equal to, or greater than Vin? Show your equations, and explain. (a) Outlet diameter is less than inlet diameter (Dout < Din) (b) Outlet and inlet diameters are equal (Dout = Din) (c) Outlet diameter is greater than inlet diameter (Dout > Din)
The volume flow in a water pipe is 9000 m°/h. The pipe length is 80 m, the pipe diameter 1 m. The material data of water are a density of 1000 kg/m? and kinematic viscosity v=10® m7s. A steel pipe with roughness 0.05 mm is used. Determine the pressure drop in the pipe.
A fuel oil at a temperature of 38°C was pumped into a pipeline and filled a 2000 L tank in 2 hours. With the pipe diameter being 2 inches, the transfer made at standard atmospheric pressure and the kinematic viscosity = 2.79 x 10^-4 m^2/s, what was the flow rate of the fluid inside the pipe?
Oil Coating: A long, continuous belt is pulled upwards through a chemical oil bath at velocity V0. The belt has rectangular cross-section and has length (L), width into the paper (W). The belt picks up a film of oil of thickness h, density ρ, and dynamic viscosity μ. Gravity g tends to make the oil drain down, but the movement of the belt keeps the fluid from running off completely. Assume fully developed, steady, laminar, incompressible and two-dimensional flow of oil to answer the following questions. Assume that no pressure gradient is needed in the vertical direction to drive the film flow. Also assume that the shear stress at the air-oil interface is zero (free shear condition). Assume no-slip condition for the fluid in contact with the moving belt. Justify any other assumptions you may make. Show all steps. (a) Derive an expression for the two-dimensional velocity field inside the oil film in terms of the known parameters. Clearly indicate your co-ordinates and origin. You must…

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS