Homework Parts A and Part B Problem statement: A simply supported beam of diameter D, length L, and modulus of elasticity E is subjected to a fluid crossflow of velocity V, density p, and viscosity µ. Its center deflection d is assumed to be a function of all these variables. Part A - Rewrite this proposed function in dimensionless form. (Hint: Take L, p , and V as repeating variables.) Part B - Suppose it is known that & is independent of µ, inversely proportional to E, and dependent only upon pV², not p and separately.

Homework Parts A and Part B Problem statement: A simply supported beam of diameter D, length L, and modulus of elasticity E is subjected to a fluid crossflow of velocity V, density p, and viscosity µ. Its center deflection d is assumed to be a function of all these variables. Part A - Rewrite this proposed function in dimensionless form. (Hint: Take L, p , and V as repeating variables.) Part B - Suppose it is known that & is independent of µ, inversely proportional to E, and dependent only upon pV², not p and separately.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.19P: 5.19 Suppose that the graph below shows measured values of for air in forced convection over a...

See similar textbooks

Similar questions

5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.
5.19 Suppose that the graph below shows measured values of for air in forced convection over a cylinder of diameter D. plotted on a logarithmic graph of as a function of ReD Pr. Write an appropriate dimensionless correlation for the average Nusselt number for these data and state any limitations to your equation.
The drag on an airplane wing in flight is known to be a function of the density of air (), the viscosity of air(), the free-stream velocity (U), a characteristic dimension of the wing (s), and the shear stress on the surface of the wing (s). Show that the dimensionless drag, sU2, can be expressed as a function of the Reynolds number, Us.
Important variables in a particular water machine are: Fluid density (ρ), impeller angular velocity (ω), impeller diameter (D), volume flow rate (), fluid viscosity (µ), head (gH). In fact, (gH) shows the energy that the fluid unit mass receives from or gives to the machine, independent of gravitational acceleration (g). Therefore, gH value is used instead of H. Important sizes in terms of the operation of the water machine are power (P), (gH) and efficiency ( h). Derive dimensionless numbers by typing these two parameters based on the above variables and applying Buckingham's p method (repeating variables method).
% ParametersD = 0.1; % Diameter of the tube (m)L = 1.0; % Length of the tube bundle (m)N = 8; % Number of tubes in the bundleU = 1.0; % Inlet velocity (m/s)rho = 1.2; % Density of the fluid (kg/m^3)mu = 0.01; % Dynamic viscosity of the fluid (Pa.s) % Define the grid size and time stepdx = D/10; % Spatial step size (m)dy = L/10; % Spatial step size (m)dt = 0.01; % Time step size (s) % Calculate the number of grid points in each directionnx = ceil(D/dx) + 1;ny = ceil(L/dy) + 1; % Create the velocity matrixU_matrix = U * ones(nx, ny); % Perform the iterationsfor iter = 1:100 % Calculate the velocity gradients dUdx = (U_matrix(:, 2:end) - U_matrix(:, 1:end-1)) / dx; dUdy = (U_matrix(2:end, :) - U_matrix(1:end-1, :)) / dy; % Calculate the pressure gradients dpdx = -mu * dUdx; dpdy = -mu * dUdy; % Calculate the change in velocity dU = dt * (dpdx / rho); % Update the velocity matrix U_matrix(:, 2:end-1) = U_matrix(:, 2:end-1) + dU; % Apply…
01: The drag force (F) of an aircraft during flight depends upon the length of aircraft flow velocity air viscosity density p. and bulk modulus of air K. (1) Derive the relationship between the above variables and the drag force by using Buckingham's II theorem . (2) Explain the physical meaning of the obtained dimensionless groups .
A simply supported beam of diameter D , length L , and modulusof elasticity E is subjected to a fluid crossflow of velocityV , density ρ , and viscosity μ . Its center deflection δ isassumed to be a function of all these variables. ( a ) Rewritethis proposed function in dimensionless form. ( b ) Suppose itis known that δ is independent of μ , inversely proportionalto E , and dependent only on ρ V 2 , not ρ and V separately.Simplify the dimensionless function accordingly. Hint:Take L , ρ , and V as r e peating variables.
Fluid mechanics theory The power input P to a centrifugal pump is a function of the volume flow Q, impeller diameter D, rotational rate ω, and the density ρ and viscosity μ of the fluid. Determine the three dimensionless numbers. Use M, L, T as your primary dimensions and ω, ρ and D as repeatingvariables.
The power P required to drive a propeller is known to depend on the diameter of the propeller D, the density of fluid ρ, the speed of sound a, the angular velocity of the propeller ω, the freestream velocity V , and the viscosity of the fluid µ. (a) How many dimensionless groups characterize this problem? (b) If the effects of viscosity are neglected, and if the speed of sound is not an important variable, express the relationship between power and the other variables in nondimensional form. (c) A one-half scale model of a propeller is built, and it uses Pm horsepower when running at a speed ωm. If the full-scale propeller in the same fluid runs at ωm/2, what is its power consumption in terms of Pm if the functional dependence found in part (b) holds? What freestream velocity should be used for the model test?
Use dimentional analysis to evaluate that in a problem involving shallow water waves (figure 6), both the Froude number and the Reynold's number are relevant dimensionless parameters. The wave speed, c of waves on the surface of a liquid is a function of depth h, gravitational acceleration g, fluid density, p and fluid viscosity μ. Manipulate your II's to get the parameters into the following form: Fr = c/(gh)1/2= f(Re) , where Re = pch/μ
A simply supported beam of diameter D, length L, and modulus of elasticity E is subjected to a fluid crossflow of velocity V, density p, and viscosity u. Its center deflection & is assumed to be a function of all these variables. Part A-Rewrite this proposed function in dimensionless form.
Measurements at a certain point of a pipe have been done where the following parameters were recorded: Fluid of density = 887 kg/m3, Fluid velocity = 4 m/s, Pressure= 11.3 KN/m2 If the total energy per unit weight at this point = 32 m, then the potential energy is: