Answered: P kN A B C D 4.5 m 3 m 9 m Figure Q2: A…

Engineering

Civil Engineering

P kN A B C D 4.5 m 3 m 9 m Figure Q2: A Simply Supported Beam

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.9.4P

See similar textbooks

Related questions

Q: Question 4 1p Four wheel loads rolls as a unit across a 18-m span. The loads are 50 kN, 40 kN, 30…

Q: Determine the maximum moment of a 8 meter long simple beam carrying a uniformly distributed load of…

A: Given: The length of the beam is 8 m. The load on the beam is 10 kN/m. Consider the figure,

Q: 1) A truck and trailer combination having the axle loads as shown in the figure rolls across the…

Q: A flat slab is supported on 600 mm dia circular columns spaced 8 m x 6 m apart in both directions.…

Q: A 100 mm x 200 mm beam 6 m long is supported by a roller at its ends and at midspan. It carries a…

Q: A continuous beam carries different loads as shown in the figure. If the moment of inertia of spans…

Q: Distributed Loads Replace the loading on the beam shown with an equivalent resultant force and…

Q: A floor plan of a general office building has 5 columns evenly spaced at 30 ft. in each direction.…

A: Area of floor plan supported by interior column = (b/2 + b/2)2 A = (30/2 +30/2)2 = 900sqfeet

Q: A rectangular beam reinforced for tension has b = 300 mm, d = 480 mm. The beam is reinforced with 7…

A: Ee have to determine the value of maximum value of concentrated live load that can be applied at the…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

Q: PROBLEM 1 Find the support reactions and joint force of the bridge construction, shown on the…

Q: Solid Mechanics .. Replace the loading by an equivalent resultant force and specify its location on…

A: Note:- The value of x is not given so solving the question by taking it as x only. The answer can be…

Q: A cantilever beam has a span of 6 m and carries a concentrated load at its free end. bf = 0.210 m…

A: Given data: L=6 m Sx = 0.002077 m3 Fy = 248 MPa

Q: 5. How do point loads and uniform distributed load be represented in SFD? a) Horizontal lines and…

A: Answer:- 5 . c 6. d 7. no clear udl mentioned over span 8. b 9. b

Q: A cast-iron beam 10 m long and supported as shown, carries a uniformly distributed load of intensity…

A: A uniformly distributed load is a load that is separated across the whole member of an element such…

Q: For questions 1A, 1B, and 1C. The figure below shows the reinforced concrete beam AB of a tourist…

A: Given data: Load=2500 N/m It is asked to find maximum shear force and Bending moment.

Q: The beam supports the loads as shown in the figure. Using E=200 GPa, w = 22 kN/m, P = 35 kN and M =…

Q: Figure 1 shows the plan view of a single- level reinforced concrete building (rooftop). The length…

A: Given:- The length of the short span = 6 m The length of the long span = 8 m The magnitude of the…

Q: A uniform load of 2000 N/m, 5 m Long crosses a girder of 20 m span from left to right. Calculate the…

A: Given data:

Q: A simply supported beam ABC of length carries a concentrated load P at an intermediate point B. If…

A: Given, Slope at A = 0.75×slope at C θA= 0.75θc

Q: Q1: At a certain section, beam has the cross-section shown in Figure (1) below. The beam is simply…

A: L = Length of beam = 3 mP = Load = 450 KN

Q: A 100 mm x 200 mm beam 6 m long is supported by a roller at its ends and at midspan. It carries a…

A: Given data: Cross-sectional area=100×200 mm

Q: Below is a moment diagram of a certain beam. 2(m) 2(m) 2(m) 1(m) 3.32 2.96 Mx n=2 -2.04 -2.4 1.…

Q: maximum shear force and the maximum bending moment.

Q: In addition to the design snow load computed in practice problem 3, the roof of the building in…

Q: Question 1 i) Determine the support reactions and ii) Sketch the axial load, shear force and bending…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Problem A: The beam shown is part of a walkway of a gymnasium. The beam ABC can be considered simply…

Q: PROBLEM 03: A truck and trailer combination having the axle loads as shown in the figure rolls…

Q: A reinforced concrete girder having a simple span of 8 m carries a uniform service dead load of 20…

A: Uniform service dead load= 20 kN/m Uniform service live load= 36 kN/m Width of beam=450 mm Depth of…

Q: W1 9 ft 13 ft (ft) 9. 22. Load Dianram M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A;…

A: To find Moment about point A Resultant force Fr Distance of Resultant force from point A.

Q: A simply supported rectangular beam, 120mm by 400mm deep, carries a uniformly distributed load of…

Q: The floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5…

A: Solution-The given velues are as follows,The dead load =1.5kPaThe live load=1.9kPaTo DetermineThe…

Q: M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and w1 = 1.5 kips/ft is distributed…

A: Solution: Convert the udl into singular concentrated load: P2=load x length =1.5 ×22P2=33 kN The…

Q: A flat slab is supported on 600 mm dia circular columns spaced 8 mx 6 m apart in both directions.…

Q: Draw the shear force and bending moment diagram for the following loading diagram as given below. 9…

A: It is asked to draw shear force and bending moment diagram.

Q: The reinforced concrete beams of a floor system are spaced at 8 ft on-center and are supporting a…

A: Given : Reinforced concrete beam of a floor system spaced at 8 ft Dead load = 50psf Live load = 80…

Q: 8m 5m The 100 mm thick concrete slab shown weighs 24 kN per cu. meter and is being supported by…

A: Given data: 100 mm thick slab unit weight of slab = 24 kN/m3 girders are spacing = 1m Dimension of…

Q: 9 ft 13 ft 22. Inad Nianram M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and W = 1.…

A: P1=12kips W1=1.5kips/ft To find resultant force and it's location from point A

Q: The continuous beam with two unequal spans as shown is subjected to a uniformly distributed load of…

Q: A uniform load of 2000 N/m, 5 m Long crosses a girder of 20m span from left to right. Calculate the…

Q: The 9.75 m long beam is simply supported at A and B shown below with a uniformly distributed load…

Q: 9 ft 13 ft 22. Inad Nianram M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and wi =…

A: To find resultant force, location of resultant force from A

Q: 24 KN/m B 2.00 m 4.00m H 5 Panels @ 3.00 m = 15.00 meters PROBLEM NUMBER 1: In the given cantilever…

Q: 1) A truck and trailer combination having the axle loads as shown in the figure rolls across the…

Q: A rectangular doubly-reinforced beam 450 mm wide and reinforced by 5-32mm diameter bars for tension…

A: Depth of compression block Xc = (m *f'cm*f'c +fy) d m = modular ratio = 2803*f'c =2803*20.7 =4.5…

Q: Figure 3 below shows a 4 m length of beam with a fixed end support at D. The beam carries a…

Q: 2. Determine the fixed-joint force vectors and the equivalent joint load vectors for the beam shown.…

Q: A simply supported beam 4 m long is composed of two C 200 x 28 channels riveted back to back.…

A: Given: The length of the beam is 4 m. The maximum flexural stress is 120 MPa. The beam consists of 2…

Concept explainers

Applications of Concrete Framing Systems

A concrete frame is a structure formed by the interconnection of beams and columns to form a structural network. In simple terms, it is the basic skeletal structure of a building or any construction. The concrete framing structure is built on a concrete foundation that forms the base of the entire structure. The concrete frame system is built to support floors, roofs, walls, beams, rafters, joists, etc.

Question

A heavy storage warehouse building is made of 200 mm thick stone concrete floor. The floor slab having a length of 9 m and width of 4 m is directly over the top of the simply supported beam as shown in Figure Q2 as in APPENDIX II. The beam is made from reinforcement concrete with the size 250 mm x 300 mm. The combination of dead load and live load will be provided with the resultant force, P at point C. The beam is supported with roller support at both ends A and B. Given the value of elastic modulus, E= 200 kN/mm2. Calculate the resultant force (P) and evaluate the slope and deflection at point D using the Macaulay method.

P kN
A
B
C
D
4.5 m
3 m
9 m
Figure Q2: A Simply Supported Beam

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Applications of Concrete Framing Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A built-upsection is to be used as a girder. It is simply supported over a span of 9 meters and laterally supported at supports and midspan. Use Fy=345MPa and Cb=1.0 Properties of the section: A=12,620mm2 d=450 mm tw=10 mm bf=300mm tf=14mm rx=203.88mm ry=70.67 mm Ix=524.59x106mm4 a.Determine the elastic section modulus, Sx. b.Determine the plastic section modulus, Zx. c.Determine the compactness of the section. d.Determine the lateral support condition. e.Determine the Allowable Flexural Strength of the girder. f.Determine the Ultimate Flexural Strength of the girder.
19 - In the plane truss system, the loading status of which is evident in the figure, the support reactions and all rod forces will be found. A is the fixed joint and B is the sliding joint. Single upload P = 35 kN, dimensions a = 1 m and bar numbers are given. Accordingly, S5 = ? A) 140B) 35C) 70D) 99E) 49.5
34 - A support is a fixed, B support is a sliding joint. loads M= 30 kNm, P1= 12 kN, P2= 13 kN, q1= 6 kN ⁄ m, q2= 7 kN ⁄ m , spans are a= 2 m, b= 3 m. The support reactions in the beam whose loading condition is given in the figure will be found. Accordingly, Ax = ?A) 22.25B) 0C) None.D) 39.25E) 21/2
16 -The stair beam in the figure will have support reactions. A support is a fixed, B support is a sliding joint. loads P1= 15 kN, P2= 30 kN, dimensions a = 2 m, b = 6 m, c = 4 m. Accordingly, Bx = ?A) 3.75B) None.C) 18.75D) 0E) 30
The steel is supported by the steel tie rod in AB beam B. Steel connection tension rod is placed 2 meters to the left of B and C sliding bracket is placed and P is loaded between AC It is. By ignoring the weights of beams and connecting rods, they can be determine the largest P load it can carry. The diameter of the BD rod is 16 mm. E = 200GPa I = 150x106mm4
Q) Determine the elastic and plastic moment of resistance of the RC beam. The beam is a trapezoid in shape. B1 at top = 300mm, B2 at bottom = 500mm, total height = 600mm, height from top to the bottom of the steel reinforcement = 570mm, As = 1473mm^2, Fy=350MPa, Fcu=30MPa Solve this early I upvote
12 A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 6.8 m long, fixed at the top and bottom, and has additional support in the weak direction at mid-height. Properties of the section are as follows: A = 14,500 mm^2 Ix = 258.6 x 10^6 mm^4 Iy = 84.375 x 10^6 mm^4 Calculate the critical slenderness ratio with respect to weak axis buckling using theoretical value of k.
In the loaded truss shown, AB=BC=CD=DE=3.4 m, BF=CG=GI=DH=HJ=(EK)/2=5.1 m. If the loading P=3.3 kN, calculate the force (in kN with proper sign) in member HK (correct to 1 decimal place). (sign convention: tensile force in a member is taken with positive sign)
A W12x79 of A573 Grade 60 (F, = 415 MPa) steel is used as a compression member. It is 7 m long, fixed at the top and bottom, and has additional support in the weak direction 3 m from the top. Properties of the section are: A = 14,500 mm? , Lx = 258.6 x 10° mm', I, = 84.375 x 10° mm* Calculate the critical slenderness ratio of the member. A. 26.208 B. 45.882 C. 36.706 D. 27 529 2 3. Calculate the nominal axial load capacity of the column A. 3 104 kN B. 4 851 kN C. 4 213 kN D.5 344 kN Calculate the service axial dead load if the service axial live load is twice as that of the dead load. Use LRFD A. 1 354 kN B. 992 kN C. 1 093 kN D. 634 kN
A W610 x 82 beam of A 36 steel has end reaction of 309 kN and is supported on a plate with a length of bearing of 154 mm. Fy = 248 MPa. Properties: d = 599 mm tw = 11 mm tf = 12.8 mm K = 33.88 Determine the end reaction due to web crippling.
The assembly shown in Figure P5.5 consists of a bronzerod (1) and an aluminum rod (2), each having a cross-sectional areaof 0.15 in.2. The assembly is subjected to loads P = 1,900 lb andQ = 3,200 lb, acting in the directions shown. Determine the horizontaldisplacement uB of coupling B with respect to rigid support A. UseL1 = 160 in., L2 = 40 in., E1 = 16 × 106 psi, and E2 = 10 × 106 psi.
The linkage is made using two A992 steel rods, each having a circular cross section. Determine the diameter of each rod to the nearest 1 8 in. that will support a load of P = 10 kip. Assume that the rods are pin connected at theirends. Use a factor of safety with respect to buckling of 1.8.