Answered: P1 = 4.0 kN P2 = 8.0 kN 1.0 m |A B -4.0…

Engineering

Civil Engineering

P1 = 4.0 kN P2 = 8.0 kN 1.0 m |A B -4.0 m- 1.0 m→

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Related questions

Q: A steel section ISHB 250@54.7 Kg/m of steel grade E250 is used a compression member of effective hei...

Q: A concrete wall footing with a width of 0.9m and a depth of 0.6m supports a centrally placed 0.6-m-t...

Q: The square steel tube carries 100kN of axial compressive force. Compute the compressive stress in th...

Q: Calculate the amount of lime and soda required to treat tuwo million litre (M.L.) of hard water, con...

Q: 5. Determine ỹ, which locates the centroidal axis x' for the cross-sectional area of the T-beam, and...

Q: A simply supported beam is carrying a unıform load. It the beam prop below, what is the final stress...

A: Introduction: Prestress of concrete is basically concrete in which internal stress of suitable magni...

Q: 3. Refer to the figure below. a. Determine the magnitude of F3 so that the resultant of the three fo...

Q: • L =18 in. • A = area of the specimen = 3.5 in.2 • Constant-head difference = h = 28 in. • Water...

Q: The maximum safe compressive stress in a hardened steel punch is limited to 1 GPa and the punch is u...

A: Safe Compressive stress in punch = 1GPaThickness of the plate = 20 mmUltimate shearing stress = 400 ...

Q: Given the following data: Draw the FBD( and determine the reactions at support A (Show in your solut...

Q: A "hawser" is wrapped around a fixed "capstan" to secure a ship for docking. If the tension in the r...

A: This is the problem based on belt friction. The force decreased exponentially with

Q: 3.15 Water occupies the bottom 1.0 m of a cylindrical tank. On top of the water is 0.75 m of kerosen...

A: Find gauge pressure at bottom of tank?

Q: Question 5: (Consider yielding & rupture limit states only) An L5 x 5 x ½ tension member of A242 ste...

A: Solution-Determining the nomnal strength in yelding is given below,Pn=FyAgPn is the nominal strengt...

Q: w kN m 5m- 3m 5m-

A: RA + RB = 3 + 22x5 RA + RB = 113 Taking Moment about point A Rb x 8 = 3 x 5 + 22x5x10.5 Rb = 146.2...

Q: A sample of 1346 grams of soil was taken from a 792 cu.cm test hole. It was then oven-dried and weig...

Q: Given data : Work done=3600 J Displacement=2.1 m Determine Force applied

A: Introduction : The question is related with mechanics topics . In this question we are provided with...

Q: A simply supported beam is carrying a varying load and a uniform load as shown in the figure. If the...

Q: of 2 Determine the average shear stress in the 20-mm diameter pin at A. |30 kN 5 3 B -2 m 4 m

Q: Fundamental Problem 4.41 Part A Determine the resultant force and specify where it acts on the beam ...

Q: The 4-mm diameter cable BC is made of a steel with E = 200 GPa. Knowing that the maximum stress in t...

Q: Calculate the stopping distance on a highway at an ascending gradient of 2% for a design speed of 90...

Q: * Hardness of Calcite is more than hardness of Diamond O Gypsum O Calcite O

A: We will solve this question in step no. 2

Q: Civil Engineering A sample of soil with LL of 72.8 was found to have a liquidity index of 1.21 and w...

Q: normal component of the acceleration of h is not to exceed 0.8 m/s².

A: given data- velocity (V) = 72kmph = 72(5/18) =20m/s acceleration(a) = 0.8m/s

Q: Situation 4 From the given cross-section of earthworks between A (20+200) and B (20+220) assuming bo...

A: Earthworks are engineering structures that are built by moving and/or treating large amounts of eart...

Q: A car is standing 200 m behind a bus, which is also at rest. The two start moving at the same instan...

Q: .5 Prepare a set of profile leveling notes for the survey in Figure 2-34. In addition to comput- ing...

Q: A simply supported steel beam of channel-type cross section is loaded by both the uniformly distribu...

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 13...

Q: Take your tinme on answering given: a.3.7 (m) b.10 (kN/m) c.17.5 (kN)

Q: .5 Prepare a set of profile leveling notes for the survey in Figure 2-34. In addition to comput- ing...

A: given - surveying question on levelling

Q: 00 AT&T LTE 10:15 AM e* 49% a bbl-app.learn.fresnostate.edu 1 of 2 A concrete wall footing with a wi...

Q: • A concrete wall footing with a width of 0.9m and a depth of 0.6m supports a centrally placed 0.6-m...

A: Ultimate bearing stress = 475kN/m2 width = 0.9m depth = 0.6m thickness = 0.6m Factor of safety= 5 Co...

Q: A steel beam is of cross section of right triangle of dimension 40 mm wide and 60 mm wide and 60 mm ...

Q: If Froude's law of similitude exists between a model and a prototype then the power ratio P, is 3.5 ...

Q: A ball at the end of a cord 1.00 meter long is swinging in a complete vertical circle with just enou...

Q: 1O KN A 6 m 6 m

Q: Determine the reactions at the support. 3 kN -2 m 2 kN 1.5 m 2 kN 1.5 m A Ax=4kN, Ay=4.5kN, By=4.5kN...

Q: The 4-mm diameter cable BC is made of a steel with E = 200 GPa. Knowing that the maximum stress in t...

Q: 18 in. 6 in. 18 in. P A Steel B C Steel D -Aluminum 6. The compound bar ABCD has a uniform cross-sec...

Q: The truss shown has cross-sectional area of 10 in' for all members. The Young's modulus of the mater...

A: Horizontal deflection of join B using Virtual Work Method###

Q: The volume flow rate of a given fluid is 0.002 m/sec. What is the mass flow rate of that fluid havin...

Q: Determine the reactions at the support. 3 kN 2 m. 2 kN 1.5 m 2 kN 1.5 m A Ax=1.5kN, Ay=4kN, By=4.5kN...

Q: For the given frame below, determine the following: 1. Determine the fxed end moment at CD ISelect] ...

Q: A reinforced concrete beam section is "b" wide and "h" deep. It is to be reinforced with 10 mmø stir...

A: I had answered only first two steps. Because given time limit I can solve only two steps.

Q: A thin walled cylindrical pressure vessel having a radius of 0.5m and wall thickness of 25mm is subj...

Q: A car travelling 60kph is followed by another travelling 80kph. The lead car suddenly brakes to a st...

Q: Vuestion- Estimole the Lowhen EC Voluu of a Satumed Extmet of say is ta toth 1o lUm ho /om at 25% De...

A: Given data- Electrical conductivity value-EC=10 μmho/cm @25% reduction in yieldEC of irrigation wate...

Q: Problem 7. Calculate the moment at point B 2.5 k/ft 1 k/ft -20 ft- -10 ft- O-116.67KN-m O -126.67KN-...

Q: Determine the resultant force and specify where it acts on the beam measured from A. Assume w = 5kN/...

Question

with complete solution please

The beam ABC shown in the figure is simply supported at A and B and has an overhang from B to C. The loads consist of a horizontal force P1 = 4.0 kN acting at the end of a vertical arm and a vertical force P2 = 8.0 kN acting at the end of the overhang. Determine the shear force V and bending moment M at a cross section located 3.0 m from the left-hand support. (Note: Disregard the widths of the beam and vertical arm and use centerline dimensions when making calculations.)

P1 = 4.0 kN
P2 = 8.0 kN
1.0 m
|A
B
-4.0 m-
1.0 m→

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve this mcq
Two smooth pipes, each having a mass of 300 kg, are supported by theforked tines of the tractor shown. Draw the free-body diagrams for each pipe and both pipes together.
An open tank contains 5.7 m water covered with 2.8 m kerosine (y= 8.0 kN/m^3). Find the gage pressure at the interface and at the bottom of the tank.
PROBLEM 1: The homogeneous structure shown weighs 21.45 kN per square meter of cross-section. The structure is subject to horizontal uniformly distributed load P1 and triangularly distributed load P2 perpendicular to side AB. Given: H1 = 9 m; H2 = 6 m; H3 = 12 m X1 = 6 m; X2 = 5 m P1 = 220 kN/m; P2 = 280 kN/m Required Answer Equivalent force of uniform load P1 1980.00 Total weight of the structure, W 3603.60 Horizontal component of the resultant, Rx 300.00
A cylindrical tank has a mean radius of 40 cm and thickness of 10 cm. It is subjected to an external pressure of 140 kg/cm2 and maximum internal pressure is 900 kg/cm2 . Determine the maximum internal tangential stress of the tank. A. 3,884.7 kg/cm2 C. 1.7684 kg/cm2 B. 4,623.6 kg/cm2 D. 2,947.5 kg/cm2
PROBLEM 1: The homogeneous structure shown weighs 21.45 kN per square meter of cross-section. The structure is subject to horizontal uniformly distributed load P1 and triangularly distributed load P2 perpendicular to side AB. Given: H1 = 9 m; H2 = 6 m; H3 = 12 m X1 = 6 m; X2 = 5 m P1 = 220 kN/m; P2 = 280 kN/m 4 Magnitude of resultant, R 4314.04 5 Angle of resultant direction from x-axis, θx 86.01 6 Distance of resultant from C measured along line CD, X 9.116
determine the resultant of the forces : A = 800N at 40degrees , B=600N at 160degrees and C=200N at 300 degrees
An equilateral triangle plate of side 2.4 m placed horizontally in a liquid (sp. gr. =0.80) in such a way that the center of the plate is 2.5 m below the free surface of water. a. Determine the area (in sq.meters) of the plate b. Determine the magnitude of the resultant force on the plate.
In natural state, a moist soil has a volume of 0.33 ft3 and weighs 39.93 lb. The oven dry weight of the soil is 34.54 lb. If Gs= 2.71, calculate the moist unit weight in lb/ft3. CHOICES: a.68.74 b.104.67 c.124.4 d.121.0
Water of density ρ flows in an open channel of constant width w with an initial depth of H1. At some point, the bottom rises smoothly to a height H3 and the depth of the water decreases to H2, as shown in Figure P10.18. If the upstream Froude number F1 = 0.4, and the downstream Froude number F2 = 1.0: (a) Find H2/H1 (this is a number). (b) Find H3/H1 (this is a number). (c) Find the force Fx exerted by the water on the step in the horizontal direction. Express the result in terms of the non-dimensional force coefficient using ρ, g, w, and H2 (this is a number). Show all your working, and state all your assumptions. Viscous forces can be neglected.
In natural state, a moist soil has a volume of 0.33 ft3 and weighs 39.93 lb. The oven dry weight of the soil is 34.54 lb. If Gs= 2.71, calculate the moist unit weight in lb/ft3. a.124.4 b.121.0 c.104.67 d.68.74
Determine P and Ra.