P1: Determine the total resistance in the circuit below when all independentcurrent sources are open circuited.P2:Solve the circuit by meshanalysis and find the current I, and the voltage across Ry.4 VR2RaIs,2AIs,4 AR4www.solved-problems.com

Answered: Image /qna-images/answer/90b410d9-523e-4fe2-b258-2bb072046c22.jpg

Answered: P1: Determine the total resistance in…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 12PP: In an R-L parallel circuit, ET=480 volts, R=16, and XL=24. Find PF.

See similar textbooks

Similar questions

In an R-L parallel circuit, ET=208 volts, R=2.4k, and XL=1.8k. Find IT.
Question: In the circuit to the right, R1 = R2,W/L = 3, Vtn = 0.6 V, and Kn = 200 A/V2. Determine the values of R1 and R2 such that VD = 1 V and Vs = -1 V.
Using Kirchhoff's Rules, compute the current (mA) and voltage (V) values of the circuit if R1=2kΩ and R2=7kΩ.
If we measure the voltage at the terminals of a two-terminal network with two known (anddifferent) resistive loads attached, we can determine the Thévenin and Norton equivalentcircuits. When a 2.2-kΩ load is attached to a two-terminal circuit, the load voltage is 4.4 V. When the load is increased to 10 kΩ, the load voltage becomes 5 V. Find the Thévenin voltage and resistance for this circuit.
The node voltage equation for node b is to be expressed in the form: K=A⋅Va+B⋅Vb+C⋅Vc, where A, B, C, and K are constants. If K=3, what should be the value of the coefficient B? what will be the value of the coefficient C?
Design a circuit that will have an outcome of the highest equivalent resistance across the terminals with a 30Vdc source. Given that the R1 = 10 R2 = 50 R3 = 85. Determine the equivalent resistance from the combination of resistors, R123, R12, R23, and R1.
The Wheatstone bridge in the circuit is balanced when R3 equals 3000 ohm. If the galvanometer has a resistance of 32 ohm, how much current in microampere will the galvanometer detect, when the bridge is unbalanced by setting R3 to 3003 ohm? Take v = 19 V. (Hint: Find the Thevenin equivalent with respect to the galvanometer terminals when R3 = 3003 ohm. Note that once we have found this Thevenin equivalent, it is easy to find the amount of unbalanced current in the galvanometer branch for different galvanometer movements.)
Consider the circuit diagram below. The circuit supplies power to the unknownresistive load, L. Determine the Thevenin equivalent circuit for the supply circuit.Verify that your Thevenin equivalent is indeed equivalent to the original circuitby simulating both circuits using CircuitJS and reporting the load current in each.Attach an exported image or screen shot of both of your circuits from CircuitJSwith the current and voltage “shown” (colors are shown on the diagram).
After transforming R2, R3, and R5 from wye connection to delta connection, what are the values of the resistances (in ohms) of the resulting delta connection? List them in any order below
Nodal analysis is another very useful way to obtain information regarding a circuit.electric. For example, consider the 4 Ω resistor in the circuit shown below. Nodal tension to your left was named V1, while the right was named V2. Therefore, determine the values of these tensions. answer:v1 = 9,43 V ; v2 = 11,15 V
following equation applies: V = IR. Outside of the linear range, V*IR, outside of the linear ranges where resistors are broken The resistor has a resistance of 100ohm, and a power rating of 250mW. 1) Sketch the plot (and label) of the i-v relationship for the resistor using only the linear range of the resistor. Determine the range of values for the voltage and current that the resistor operates as a linear element and note these simplified numerical values on the plot.
Find the equivalent resistance Rab (in ohms) of the circuit shown by using a Wye-to-Delta transformation involving resistors R2, R3, and R5. After transforming R2, R3, and R5 from wye connection to delta connection, what are the values of the resistances (in ohms) of the resulting delta connection? List them in any order below.

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

P1: Determine the total resistance in the circuit below when all independent current sources are open circuited. P2: Solve the circuit by mesh analysis and find the current I, and the voltage across Ro. 4V R2 Ra Is, 2A Is, 4 A R4 www.solved-problems.com