P12.29. Draw the influence lines for the bar forces in members DE, DI, EI, and IJ if the live load in Figure P12.29 is applied through the lower chord panel points. C D E 5' F B LK J H 6 @ 15' 90' I G T 15'

P12.29. Draw the influence lines for the bar forces in members DE, DI, EI, and IJ if the live load in Figure P12.29 is applied through the lower chord panel points. C D E 5' F B LK J H 6 @ 15' 90' I G T 15'

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter8: Influence Lines

Section: Chapter Questions

Problem 42P

See similar textbooks

Related questions

Q: Question 17 A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the…

Q: Consider the cantilever beam shown below. A triangular distributed load of with a maximum value of 2…

Q: Solve for the discharge of the weir having a head of 0.30m in L/s. 1.If a 90° triangular weir is…

Q: 3. If a contracted rectangular sharp crested weir, 2m long is used. a. 587 c. 523 d. 563 b. 532

Q: A laboratory sample of clay 2 cm thick took 15 min to attain 60 percent consolidation under a double…

Q: Asap thank you. a. Ordinate of the influence line of RC at point D b. Ordinate of the influence line…

Q: The 2.4kg particle moves in the horizontal x-y plane and has the velocity shown at time t=0. If the…

A: Given data Mass of particle = 2.4kg Force = Fy = 2 + 3t2/4 Initial velocity = Vi = 5m/s Let the…

Q: The motion of a particle is defined by the relation x = 5t4 - 4t³ + 3t - 2, where x and t are…

Q: What length of a Cipolletti weir should be constructed in order that the head. of flow will be 0.96…

Q: A 90m by 90m lot is to be divided into 9 equal square sections. The elevations of the ground surface…

Q: 60 k. ft DETERMINE THE SHEAR AND AND MOMENT MOMENT FOR EVERY 8-FT STRIP INTERVAL STARTING AT POINT A…

Q: A certain horizontal curve on a 6-lane highway (3 lanes each direction with no median) has a…

A: The given data is: Super elevation=9% Central angle=26.1 degrees Road width=11.4 ft Shoulder…

Q: support reactions and moment

Q: The compression diagram for a precompressed clay indicates that it had been compressed under a…

Q: Situation 6: A steel plate is 280 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the…

Q: A long braced cut shown is supporting a layer of clay. Angle of fraction is 0. The struts are placed…

Q: Determine the magnitude of the tension at support B (N). Supports are pin connected B.) Determine…

Q: 150 x 250 mm rectangle beam carries a uniform distributed load of W kN/m over its entire span. The…

Q: Situation 9: A steel plate is 250 mm wide and 10 mm thick with 4 bolts (22mm dia) cut into the plate…

Q: = All the tension/compression members of the frame structure shown in the figure are pin-jointed and…

Q: Carry out an enviromental asessment of a new educational building using industry standard techniques…

Q: V₂ V₂ Vw air water solids Ww W - 10% Ys=165.4 lbf/ft³ Y: 127.0 lbf/ft³. Yx

Q: The following data are from a direct shear test on an undisturbed soil sample. Represent the data by…

Q: The steel tie-bar shown in the figure has been designed to carry a tension force of 98 kN when…

A: Shear Stress: The force which affects the bolts when two or more components or bolts are connected…

Q: A 4 m W B 2m C

A: An overhanging beam is given of length = 12m in which uniformly distributed load is acting. It has…

Q: (lb) 4 900 -900 480 4 -1380 x (ft)

Q: A simply supported rectangular concrete beam has a clear span of 6m. Has a width of 400 mm and has…

Q: SFD and BMD. Locate points of cont the elastic curve and compute the de 8 kN 8 kN 20 kN-m C

Q: Design a lintel over an opening of 3.5 m. The lintel is made in a wall 400 mm thick. The lintel has…

Q: Given the data of a continuous solid one-way slab. Spans given are all clear spans. For shear and…

Q: Q1/ A ball is released from the Point A upward with a velocity of 25 m/s. If the ball strikes in the…

Q: Find the depth in furlong of the ocean (SG = 1.03) if the pressure at the sea bed is 2,032.56 kpag.…

Q: B 3 m A 4 m D C 4 m E P

Q: Find the value dry unit weight Bulk unit weight=19.07 KN/m3 Water content of soil-0.03

A: Given data : The value of water content of soil w=0.03 The value of bulk unit weight γ=19.07 KN/m3…

Q: The circular shaft AB consists of a 19.4 mm diameter solid steel cylinder in which a 10.6 mm…

Q: Problem. Draw the shear and moment diagram of the beam loaded as shown in Fig 60 KN 30 kN 2m R₂ R₁…

A: The length of beam, l=7mThe support reactions are R1A support & R2B supportThe loads applied ar…

Q: P12.1. Draw the influence lines for the reaction at A and for the shear and moment at points B and…

Q: 1. A member is formed by connecting a steel bar to an aluminum bar is shown. Assuming that the bars…

Q: Compute the value of stress Tensile load=22 N Cross sectional area=2 mm2

A: Given data Tensile load (P) = 22 N Cross sectional area (A) = 2 mm2

Q: Design a lintel over an opening of 3.5 m. The lintel is made in a wall 400 mm thick. The lintel has…

Q: Subject: Soil Mechanics Please provide a solution and a diagram For a laboratory consolidation…

Q: A clay layer 5 m thick has double drainage. It was consolidated under a load of 127.5 kN/m2. The…

Q: A W 14 x 142 is used as a column having length of 9 m long. It is hinged at the upper end and fixed…

Q: B. Q): Compute the balanced axial load and moment capacity of the column shown in Figure below. Use…

A: Axial load carrying capacity of the column Pu=0.8*0.650.85 f'c Ac +As fy Ac=350*350-6*π4*202=…

Q: • Determine the SLOPE AND DISPLACEMENT at point A. TAKE E = I1 GPA. THE VALUE OF "I" CAN BE SOLVED…

Q: Provide complete solution. A frustum of a cone is shown, with the orifice at the bottom. C_d=0.62.…

Q: The beam shown in the figure is supported at roller A and pinned at B and has a 36 kN/m over 1.5 m…

Q: the support reactions and moment ing thro quation

Q: 4. A rod which tapers uniformly from 5 cm to 3 cm diameter in a length of 50 cm, is subjected to an…

Q: Find the value of that will make lines a and b parallel. (5x - 32) 52° a b

A: Given, two angles, (5x-32) and 52 value of x = ? (5x-32) =52

Concept explainers

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.

Question

P12.29. Draw the influence lines for the bar forces in
members DE, DI, EI, and IJif the live load in Figure P12.29
is applied through the lower chord panel points.
с
D
E
F
B
00
00
00
L K J1
H
6 @ 15' 90' -
P12.29
68
aduk
5'
15'

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Trending now

This is a popular solution!

Step by step

Solved in 10 steps with 23 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw the influence lines for bar forces in mem- bers HD and HC of the truss shown in Figure P12.33. The load moves along the bottom chord of the truss. If the truss is to be designed for a uniform live load of 0.32 kip/ft that can be placed anywhere on the span in addition to a concentrated live load of 13 kips that can be positioned where it will produce the largest force, compute the maxi- mum tension and compression forces in bar HD.
The horizontal load P can act at any location along the length of member AC shown in Figure P12.26. Draw the influence lines for the moment and shear at section 1, and the moment at section 2.
(a) Load is applied to the three-hinged trussed arch in Figure P12.40 through the upper chord panel points by a floor beam and stringer floor system. Draw the influence lines for the horizontal and vertical reac- tions at support A and the forces or components of force in members BC, CM, and ML. (b) Assuming that the dead load of the arch and floor system can be represented by a uniform load of 4.8 kips/ft, determine the forces in bars CM and ML produced by the dead load. (c) If the live load is represented by a uniformly distributed load of 0.8 kip/ft of variable length and a concentrated load of 20 kips, determine the maximum force in bar CM produced by the live load. Consider both tension and compression. Joint E acts as a hinge.
Draw the influence lines for vertical reactions at supports B and D and the shear and bending moment at point C of the beam shown infigures P8.5, use Muller-Breslau’s Principle. PLEASE REFER TO FIG. P8.5
"Draw the influence lines for vertical reactions at sup-portsAandCand the shear and bending moment at pointBof the beam shown in Fig. P8.6"
"Draw the influence lines for the vertical reaction and thereaction moment at supportAand the shear and bendingmoment at pointBof the cantilever beam shown in Fig. P8.5"
In the figure, draw the influence lines for the reactions Ax and Ay at the left pin support and the bending moment at section 1 located at the face of column AB using ONLY EQUILIBRIUM METHOD. If a uniform live of 0.8 kips/ft is applied on top of the frame, compare the bending moments at section 1 if the live load is only applied on top of the entire span BC, CD, and BD. Discussion the variations and which is the critical loading scenario
########~~~~~~~~~~~~Draw the influence lines for the vertical, shear and moment reaction at support C and E of the beam shown below.#########~~~~~~~~~~~~~~~~ Answer correctly I'll rate!
Recompute the reactions for the frame in Fig-ure P9.43 if support C settles 0.36 in. when the load actsand support A is constructed 0.24 in. above its intendedposition. Given: E = 30,000 kips/in.2 and I = 60 in.4
Question (2) For the beam shown in figure (2), draw the influence lines for: 1. ReactionsatjointsA,C.andF. 2. ShearforceatjointB. 3. Bending moment at joint E.
Draw the influence lines for members DK and CI assuming that the loads in the illustrated truss are being transmitted to the bottom chord. Considering the provided 3 - point moving load, calculate the following member forces. Assume that the loads only move to the right. Questions a. Maximum tension on member DK in kN. b. Maximum compression on member DK in kN. c. Maximum tension on member CI in kN. d. Maximum compression on member CI in kN.
Load moves along girder BCDE. Draw the influence lines for the reactions at supports A and D, the shear and moment at section C, and the moment at D. Point C is located directly above support A.