Parameter Notation Value Voltage at maximum power point Open-circuit voltage Short-circuit current |Current at maximum power point Power rating Length of module Breadth of module Temperature coefficient of maximum power Temperature coefficient of open-circuit voltage %/C Temperature coefficient of short-circuit current %/C Number of cells Number of by-pass diodes Vmpp (STC) (V) Voc (STC) (V) Isc (STC) (A) Impp (STC) (A) PM (STC) (W) Lmod (m) Bmod (m) 38.4 46.2 8.95 8.33 320 0.982 1.955 %/C -0.41 -0.31 0.052 72 3 What is the value of the voltage if the temperature rises from the STC condition to 35 C? 35.3 34.3 119.04 38.4

Parameter Notation Value Voltage at maximum power point Open-circuit voltage Short-circuit current |Current at maximum power point Power rating Length of module Breadth of module Temperature coefficient of maximum power Temperature coefficient of open-circuit voltage %/C Temperature coefficient of short-circuit current %/C Number of cells Number of by-pass diodes Vmpp (STC) (V) Voc (STC) (V) Isc (STC) (A) Impp (STC) (A) PM (STC) (W) Lmod (m) Bmod (m) 38.4 46.2 8.95 8.33 320 0.982 1.955 %/C -0.41 -0.31 0.052 72 3 What is the value of the voltage if the temperature rises from the STC condition to 35 C? 35.3 34.3 119.04 38.4

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and current relationships change? (a) If C1 is the complex positive-sequence voltage gain in Problem 3.29 and (b) if C2 is the negative sequence complex voltage gain, express the relationship between C1andC2
With no load attached, the voltage at the terminalsof a particular power supply is 50.8 V. When a 10-Wload is attached, the voltage drops to 49 V.a. Determine vS and RS for this nonideal source.b. What voltage would be measured at the terminalsin the presence of a 15- load resistor?c. How much current could be drawn from this powersupply under short-circuit conditions?
Consider the circuit of Figure 1 using VCC = 10 volts, R1 = 10 kΩ, R2 = 3.3 kΩ, Re = 4.7 kΩ and Rc = 5.6 kΩ. Using the approximation of a lightly loaded “stiff” voltage divider, determine the ideal endpoints of the DC load line and the Q point, and record these in Table 1.1. Can you show process of solution
Write a discussion and conclusion on Open Circuit and Short Circuit equivalent circuit test.
write down the overview of grid code technical requirements for high power WECS
Define three clockwise mesh current from the circuit and employ the supermesh technique to obtain a numerical value for each??
For calculating the Thevenin's Equivalent Resistance(RIh) at load terminals, remove the load resistance and if a voltage soure by a short circuit and a current source is replaced by an open circuit source is present replaced by an open circuit A_ True B_False
What is the nodal analysis/ node - voltage method? Also, please give me some circuit problems regarding the topic, solution, and book references if you have them. Thank you so much!
Using Superposition Method. Determine the voltages at the 5-ohm resistordue to the 24-Volt, 38-Volt and 4-Ampere Sources. Also, what is the totalvoltage at the said resistor? Remember: Voltage sources are shorted andcurrent sources are opened (removed) during individual source analysis
A housing estate is being built and the electrical system for each house from a range of 2 to 20-bedroom houses from single floor apartments to 3 storey buildings are on offer throughout the estate. There are commercial buildings to be constructed for shopping purposes as well. What risks exist and what are the components and methods we use to mitigate these risks both at the substation and at the consumer/ residential side. Describe how these would all fit together.
Are the following statements correct or wrong? Justify your answer.(a) GTO requires very high current applied to its gate to be turn off.(b) IGBT is a current driven device.(c) IGBT is more efficient than BJT in high power applications.(d) Thyristors are used only for low voltage, low current applications.(e) MOSFETs are used for low frequency applications. (I got the answer in the search but if possible,i want it in a slightly different way)
Can you explain in detail on how to solve this?Determine current ID graphically using load line analysis, if Zener voltage is 3V.