P.1 – Obtain the parameters Dtotal, Jtotal for the electromechanical system of Fig.1. Byusing these parameters, calculate the power Pm that the motor should supply at instantt=t,', being t=1s.'miElectricW.mGearboxloadw*= 95pmotorTmDI =0.003J1 = 0.005 Kg.mWD,=0.5Nm.s/radti =25J2=0.8 Kg.m2taWm2T¡ (Nm)115hload= 95 %SaFig. 1103.8p (rad/s)J2J total = J1 +-Ncaixa-i?T,lom, =d@m+J total·| Tm(@m1)+D¢otal •Om1dtNcaixa-i(D2 +tgaPm = Tm Pm1total = D, +Ncaixa i

Open Loop System- A system which is controllable in which input of the system does not depends on…

Answered: parameters Dtøtal, Jtotal

Engineering

Electrical Engineering

parameters Dtøtal, Jtotal

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A motor,the input to which is 20kW at 220V,is supplied by a two-core cable.400m long.If the power lost in the cable Is not to exceed 5% of the motor Input . Calculate the minimum permissible C.S.Area of the cable conductor What will be the voltage at the feeding point ? Assume the resistivity of the conductor at working temperature to be 0.02 microohm/m
Consider the head (the distance between the waterfalls) of the Run-of-River Hydro Power Plant is 5 meters. The design used a multi-jet Pelton wheel which has the parameters and operating conditions as below: o Flow rate, p = 4 m3/so Nozzle velocity coefficient, K = 0.98o Wheel diameter, D = 1.47o Mechanical efficiency, fl = 88%1) Calculate the highest possible power output of the turbine. 2)Estimate the electricity generation of the above hydropower plant if the river's water flow rate suddenly drops to half.
If some AC load is turned on and consumes a current =0.4 A, and electrical power produced from conversion of hydro plant =160W , and efficiency=60%, find: PL of AC load, and Pm of the hydro plant……….. Calculate the hydraulic power entering the distributor if the mass flow rate=0.5 kg/s , the head of the power plant=20m. ……………
1 - A square chip, with side ? = 5 mm, operates under isothermal conditions.The chip is positioned on a substrate so that its side and bottom surfaces are thermally insulated, while its top surface is exposed to theflow of a refrigerant at ?∞ = 15°C. From reliability considerations, the chip temperature cannot exceed ? = 85°C. The refrigerant being air, with a convection heat transfer coefficientcorresponding ℎ = 200 W/(m2K), what is the maximum allowable power for the chip? Since the coolant is a dielectric liquid for which ℎ = 3000 W/(m2K), what is the maximum allowed power?
To which of the following questions does an engineering economy analysis provide useful input? (a) Has the mechanical or electrical engineer chosen the most economical motor size given functional requirements? (b) Has the civil or mechanical engineer chosen the best thickness for insulating a building?(c) Has the biomedical engineer chosen the best materials for the company’s artificial knee product?(d) All of the above
The transformer in the circuit shown in Fig. 1(a) is an ideal transformer with a=1/3. The circuit is supplied from a sinusoidal ac source with a frequency 60 Hz. Determine the angular speed ω. Determine the source voltage RMS value. Express the supply voltage as a function of time. Calculate the load resistance value (9 Ω) referred to the transformer low voltage side. Calculate the circuit equivalent resistance as seen by the source. Calculate the current drawn from the supply. Calculate the load voltage Vo. Calculate the power dissipated in the 3 Ω resistor. Draw, to scale, the phasor diagram including: supply voltage, supply current, load voltage and load current.
The car of Light Railway Transit (LRT) is propelled by 660-volt DC motor connected to the DC teeder lines of rectifier station. This car is required to exert a tractive effort of 4,500 kg at a velocity of 50 km/hr. How much current will be drawn from the feeder lines if the overall efficiency of motor and the flywheel drive is 65%?
Consider a PV module with the following external parameters at STC: Pmax = 320 W, VOC = 45 V, ISC = 8 A, NOCT =40 °C and the temperature coefficient of power is −1 W/°C. a) If the ambient temperature rises to 35 °C while the irradiance is 1,000 W/m2, what is the cell leveltemperature, calculated with the NOCT model?b) What is the new power output of the PV module under the new ambient temperature of 35 °C and 1,000W/m2irradiance?
Suppose you have to install a Diesel power station with data given below: Parameter Data Number of Generating Units 4 Capacity of Each of 1st Three Units 600 kW Capacity of 4th Unit 400 kW Engine Type 4 stroke 300 rpm, airless-injection type Max. Demand of Station 2500 kW at 0.8pf lagging Average Load Factor of Station 65% Annual Capacity Factor 55% Energy Generated per Unit 2.39 kWh/kg Weight of Fuel Not specified in the provided data Generator Efficiency 90% Salaries/Wages & Operational Costs Rs. 600,000 per annum Total Maintenance Costs Rs. 330,000 per annum (1/3rd fixed, 2/3rd variable) Consumption of Lubricating Oil 1 kg for every 450 kWh Cost of Fuel Oil Rs.40/kg Cost of Lubricating Oil Rs.120/kg Cost of Power-Plant/KW Installed Rs. 95000 Insurance and Taxes 3% of the initial/capital cost of Plant Interest on Investment 7% of the initial cost of Plant Depreciation of Plant 8% of the initial cost of Plant Investigate the…
HELP ASAP!4
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:A 55000-kW thermal plant of National Power Corporation delivers an annual output of 238000000 kw-hr with a peak load of 44 MW. What is the capacity factor? 49.4% 42.4% 48.2% 44.6%
2.A. When machine losses are determined by the retardation method, it is necessary to know the machine'sA. ventilation requirements.B. resistance.C. moment of inertia.D. electrical input.2.B. If an aluminum field coil has a resistance of 120 ohms at 30 C, its corrected resistance at a temperatureof 75 C isA. 140.5 ohms.B. 141.2 ohms.C. 132.9 ohms.D. 133.3 ohms.