Part A End A of the bar AB in (Figure 1) rests on a frictionless horizontal surface, and end Bis hinged. A horizontal force F of magnitude 270 N is exerted on end A. Ignore the weight of the bar. What is the horizontal component of the force exerted by the bar on the hinge at B? Express your answer with the appropriate units. HA ? F = Value Units Submit Request Answer Part B What is the vertical component of the force exerted by the bar on the hinge at B? Express your answer with the appropriate units. HA ? Fo = Value Units Submit Request Answer

Part A End A of the bar AB in (Figure 1) rests on a frictionless horizontal surface, and end Bis hinged. A horizontal force F of magnitude 270 N is exerted on end A. Ignore the weight of the bar. What is the horizontal component of the force exerted by the bar on the hinge at B? Express your answer with the appropriate units. HA ? F = Value Units Submit Request Answer Part B What is the vertical component of the force exerted by the bar on the hinge at B? Express your answer with the appropriate units. HA ? Fo = Value Units Submit Request Answer

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section: Chapter Questions

Problem 74A

See similar textbooks

Similar questions

Check Your Understanding For the situation in described in Example 12.5, determine the values of the coefficient s of static friction for which the ladder starts slipping, given that is the angle that the ladder makes with the floor.
Find the magnitude of the tension in each supporting cable shown below. In each case, the weight of the suspended body is 100.0 N and the masses of the cables are negligible.
A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?
One end of a uniform 4.00-m-long rod of weight Fg is supported by a cable at an angle of = 37 with the rod. The other end rests against the wall, where it is held by friction as shown in Figure P12.23. The coefficient of static friction between the wall and the rod is s= 0.500. Determine tile minimum distance x from point A at which an additional object, also with the same weight Fg can be hung without causing the rod to slip at point A.
a horizontal rod (m=5.2 kg) is hinged to a wall at the left end and three forces are acting on the rod as shown in the figure: the force of gravity (mg), a tension force (T), and the force exerted by the hinge (broken into components Fx and Fy) If theta = 35 degrees, what must T be equal to in order to keep the rod static?
A uniform ladder of length L and weight w is leaning against avertical wall. The coefficient of static friction between the ladderand the floor is the same as that between the ladder andthe wall. If this coefficient of static friction is μs = 0.500, determinethe smallest angle the ladder can make with the floorwithout slipping.
How much compression acts on the hip during two-legged standing, given that the joint supports 250 N of body weight and the abduct muscles are producing 600 N of tension? What is the angle α of R?
The figure shows three boards clamped together. The center board weighs 93.5 N, and the coefficient of static friction between the boards is 0.490. What is the minimum magnitude of the horizontal compression forces (in N) acting on either side of the center board so it does not slip?
A wooden plank with a mass of 50.968 kg is supprted by two cable at its ends. At what location should a box of mass 20.387 kg be placed for one cable to exert a force of 125 N more than the other cable? Note: the location is the distance from each cable please show full solution, figure and fbd.
For the beam and loading shown, determine the tension in cable BC if P = 165.8, Q = 249.3, R = 355.4, S = 268.2, T = 117, a = 9.38, and b = 12.47. Round off only on the final answer expressed in 3 decimal places .
suppose the length L of the uniform bar is 3.4 m and its weight is 180 N. Also, let the block's weight W = 310 N and the angle 0 = 41°. The wire can withstand a maximum tension of 440 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A?