Part A Given the following electric circuit R1 Amperemeter ??? 0 The voltmeters BAT1 R2 10 0 R3 10 0 Voltmeter shows 5 Volt 9 V It is known that the voltage measured by the voltmeter is 5 Volt 1. Calculate the value of the current I through the battery BAT1 (It is the current that the amperemeter shows)

Part A Given the following electric circuit R1 Amperemeter ??? 0 The voltmeters BAT1 R2 10 0 R3 10 0 Voltmeter shows 5 Volt 9 V It is known that the voltage measured by the voltmeter is 5 Volt 1. Calculate the value of the current I through the battery BAT1 (It is the current that the amperemeter shows)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter11: Conduction In Liquids And Gases

Section: Chapter Questions

Problem 8RQ

See similar textbooks

Similar questions

Unit 10 Practical Applications You are an electrician on the job. You have been gives a multimeter that has the following AC voltage ranges: 30, 60, and 150. The meter states that it has a resistance of 5000 Ω/ V. You need to be able to measure a voltage of 277 volts. How much resistance should be inserted in series with the meter to make the 30-volt range indicate a full scale value of 300 volts?
Choose the correct answer In the USA, the heating element inside a hairdryer is marked as follows: (120V, 2400W). What is the resistance of the filament in the lamp? (HINT: Use Ohm's Law and power "law" equations). A. 10 ohm B. 4800 ohm C. 2 ohm D. 6 ohm
An electric water heater has a rating of 1 kW,230 V. The coil used as theheating element is 10m long and has a resistivity of 1.724 x 10^-6 ohm-cm. Determine the required diameter of the wire in mils? the answer is 2.52 mils (according to ECE board exam answer keys) I don't know how to get it. Can you show me?
1. [MO12] A lighting load is drawing 0.5 amps with 100 volts applied. If the light is use for 6 hours, how much energy used? Assume that the average cost of energy is P 5.00 per kilowatt-hour, find the operation cost of the bulb.2. [MO17] A branch circuit consists of five (5) convenience outlets. Determine the size of the conductor to be usedto the said branch circuit. Please indicate the type of conductors to be used.
1.A. You've assembled the following components to join two copper conductors: a mould, powdered copperoxide, powdered aluminum, and an igniter. With these components, which of the following processes willyou use to connect the conductors?A. Exothermic weldingB. Irreversible compression groundingC. Mechanical groundingD. Thermal cycling 1.B. Two electricians are discussing voltage ratings. Electrician A says that a motor that's installed 40 feetfrom a power source will show a lower applied voltage than a motor that's installed 20 feet from the samepower source. Electrician B says that an exact voltage of 240 V must be applied to a motor that's rated at240 V. Who is correct?A. Neither Electrician A nor Electrician B is correct.B. Only Electrician A is correct.C. Only Electrician B is correct.D. Both Electrician A and Electrician B are correct.
A cable one mile long and 0.50 inches in diameter is composed of a steel core 0.25 inches in diameter and the outside shell is aluminum. The resistance of the cable is _____ is Ps and Pa 57.4 and 17.5-ohm Cmil/ft, respectively Choices: a.) 0.447 ohm c.) 0.625 ohm b.) 0.893 ohm d.) 5.3 ohms
Please I want answer of this Electrical Principles question. Thanks
Calculate the voltage drop across VR1 if VR2 is equal to 11.6 volts and VR3 = 17.58 volts.
Voltage Drop! Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C. what is the Voltage Drop ? Answer?
The sizes of the given circuit elements are given below.What is the average power delivered by the Is current source?R1 = 8 ohmsR2 = 8 ohmsL1 = 9 milliHenryL2 = 8 milliHenryn = 3V0 = 50cos(1300t+30) Volts
A machine is attached to the following loads for light in the winding shop. The light affixse (electric energy) of 250 W filament lamps (electric energy) is 14.5 Lumen / Vote. There are 300 ning fixtures attached. Now 30 lumen / wat fixes with electric energy to save, is changing the HPMV 120 Ning Fixure of 150 W. If the cost of electric energy is Rs. 2.35 / KWH and the time of use of lamps is 3500 hours during the year, find the following things. (i) Savings in electric energy consumption per year (II) Savings in electric energy cost during the year (III) If the total capital investment in changing the lamp's fixture is Rs.7, 60,000 so find ROI in percentage. (IV) Pay - back period calculate in year.
4. A 1-ampere fuse has a resistance of 0.2 ohm. It will melt or blow when the instantaneous current through it is large enough to create power loss of 5 watts. What is the value of the “melting” current? answer asap provide soln