R1 ??? Q Amperemeter The voltmeters BAT1 9 V R2 10 Q R3 shows 5 Volt Voltmeter 10 Q It is known that the voltage measured by the voltmeter is 5 Volt 1. Calculate the value of the current Iat through the battery BAT1 (It is the current that the amperemeter shows) 2. Calculate the value of the Resistance R, 3. Calculate the Power provided por the battery to the system 4. Calculate the Power released by each one of the Resistances R, R,, and R, 5. Explain if there is a relation between the Power provided por the battery Pat and the Power released by the Resistances R,, R,, and R3. Justify your answer with your calculations

R1 ??? Q Amperemeter The voltmeters BAT1 9 V R2 10 Q R3 shows 5 Volt Voltmeter 10 Q It is known that the voltage measured by the voltmeter is 5 Volt 1. Calculate the value of the current Iat through the battery BAT1 (It is the current that the amperemeter shows) 2. Calculate the value of the Resistance R, 3. Calculate the Power provided por the battery to the system 4. Calculate the Power released by each one of the Resistances R, R,, and R, 5. Explain if there is a relation between the Power provided por the battery Pat and the Power released by the Resistances R,, R,, and R3. Justify your answer with your calculations

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 28RQ

See similar textbooks

Similar questions

Given:Vb = 100 voltsR = 10000 ohmsC = 200 μFAssuming that after a long period of time, the switch is flipped from position "A" to position "B" at t=0. Calculate the voltage across the resistor after 3 TC.
1.A. You've assembled the following components to join two copper conductors: a mould, powdered copperoxide, powdered aluminum, and an igniter. With these components, which of the following processes willyou use to connect the conductors?A. Exothermic weldingB. Irreversible compression groundingC. Mechanical groundingD. Thermal cycling 1.B. Two electricians are discussing voltage ratings. Electrician A says that a motor that's installed 40 feetfrom a power source will show a lower applied voltage than a motor that's installed 20 feet from the samepower source. Electrician B says that an exact voltage of 240 V must be applied to a motor that's rated at240 V. Who is correct?A. Neither Electrician A nor Electrician B is correct.B. Only Electrician A is correct.C. Only Electrician B is correct.D. Both Electrician A and Electrician B are correct.
A cable one mile long and 0.50 inches in diameter is composed of a steel core 0.25 inches in diameter and the outside shell is aluminum. The resistance of the cable is _____ is Ps and Pa 57.4 and 17.5-ohm Cmil/ft, respectively Choices: a.) 0.447 ohm c.) 0.625 ohm b.) 0.893 ohm d.) 5.3 ohms
Direction: Answer the following and show your solution. REFERENCE: a. Watch the video provided discussing what is current resistivity and resistance. i. Electric current - https://youtu.be/HXOok3mfMLM ii. Resistance - https://youtu.be/NfcgA1axPLo iii. Resistivity - https://youtu.be/nN3bb0aK1GM 1. Calculate the current density, resistance, and electrical field of a 5-m length of copper wire with a diameter of 2.053 mm (12-gauge) carrying a current of I=10mA.
Voltage Drop! Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C. what is the Voltage Drop ? Answer?
Choose the correct answer In the USA, the heating element inside a hairdryer is marked as follows: (120V, 2400W). What is the resistance of the filament in the lamp? (HINT: Use Ohm's Law and power "law" equations). A. 10 ohm B. 4800 ohm C. 2 ohm D. 6 ohm
Show the complete and step-by-step solution for an upvote. a. The voltage source value if the power dissipated by the 8 Ω resistor is 8 Joules per second. (Answer: 262.051 V) b. The power supplied in Watts by the voltage source if the power dissipated bythe 8 Ω resistor is 1 Joule per second. (Answer: 766.915 W, supplying)
Good day, sir/ma'am. Question: A battery has an emf of 14 V and internal resistance of 0.08 ohms. Its terminals are connected to a load resistance of 3.00 ohms. a.) Find the terminal voltage of the battery. b.) Calculate the power delivered to the load resistor and the power to the internal resistance of the battery. Thank you.
If a nonlinear resistor has a voltage-current relation of V = 2 I3 + 7, what power does it absorb when energized by 67 V? The final unit must be in watts, W. Round your answer to 2 decimal places. **Show your correct and complete solution. Thank you!**
a.a. Which of the following statements about grounding electrode conductors is true?A. They restrict the ground connection.B. They eliminate potential differences between conductive objects and the Earth electrode.C. They facilitate operation of overcurrent protective devices.D. They perform bonding between the Earth and grounded conductors. a.b. Which of the following formulas would you use to find current?A. R = E ÷ IB. I = R × EC. I = E ÷ RD. E = I × R
A copper conductor wire with a total length of 100ft is used in a 15 amp common household circuit has a resistance of 1.62 ohms/1000ft. If the circuit is fully loaded, determine the heat produced by the conductor? (Hint 1W = 3.413Btu/hr) a. 124.40 Btu/hr b. 99.83 Btu/hr c. 8.29 Btu/hr d. 177.50 Btu/hr
Two wires A and B made from two different materials have temperaturecoefficient of resistance equal to 0.0019 and 0.0019 ohm per degreeCelsius, respectively. It is desired to make a coil of wire having a resistance of1219 ohms with a temperature coefficient of 0.001, using suitable lengths ofthe two given wires connected in series. Determine the required length ofwire A. Put an illustration figute with compelte solutions, step by step, kindly handwritten it. THank you!