Part A Suppose that o, = 50 kPa and o, = 740 kPa. Determine the equivalent state of stress on an element at the same point that represents the maximum in-plane shear stress at the point. (Figure 1) Find the value of Tmax in-plane- Express your answer to three significant figures and include the appropria units. ? Tmax in-plane = Value Units Figure < 1 of 1 Submit Request Answer O y Part B Find the value of Javg- Ox Express your answer to three significant figures and include the appropria units. 400 kPa µA Oavg = Value Units

Part A Suppose that o, = 50 kPa and o, = 740 kPa. Determine the equivalent state of stress on an element at the same point that represents the maximum in-plane shear stress at the point. (Figure 1) Find the value of Tmax in-plane- Express your answer to three significant figures and include the appropria units. ? Tmax in-plane = Value Units Figure < 1 of 1 Submit Request Answer O y Part B Find the value of Javg- Ox Express your answer to three significant figures and include the appropria units. 400 kPa µA Oavg = Value Units

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.8P: - A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s...

See similar textbooks

Similar questions

- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
By using Hooke’s law, how can we express the dilatation interms of the applied stress?
The yield stress for a zirconium-magnesium alloy is sY = 15.3 ksi. If a machine part is made of this material and a critical point in the material is subjected to in-plane principal stresses s1 and s2 = -0.5s1, determine the magnitude of s1 that will cause yielding according to the maximum shear stress theory.
2. (a)A single thick-walled cylinder h2as an inner radius of 100 mm and an outer radius of 155 mm. The cylinder is subjected to an internal pre2 ssure of 65 ????/?? and an external pressure of 25????/?? . (i) Calculate the hoop and radial stress inside and outside of the cylinder. (ii) Sketch the 3D Mohr’s Circle of a point on the inner surface of the cylinder and label the principal stresses (include coordinates values). (iii) If the cylinder is made of a copper alloy with yield strength of 200 MPa; verify whether the cylinder will fail using the Von Mises Criteria and calculate the Factor of Safety. (b) To increase the FOS to the standards value, another cylinder is shrunk-fitted to make a compound cylinder. When the internal pressure load remains unchanged, the maximum hoop stress in the inner cylinder of the compound cylinder has been found to be reduced by 5% of the original value(i)Calculate the interface pressure at the common radius of the compound cylinder. (ii)Assume the…
Using Mohr's circle on each case, determine a)The principal stresses and maximun shear stress. Show all results on sketches of properly oriented elements b)Is there the invariance of normal stresses in each case?
I need help on solving this question, there are 3 parts: a) find the factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion) b) find the Mises equivalent stresses at point H can be calculated as ______ MPa c) find the factors of safety at point H predicted by the maximum-distorsion-energy theory (Von Mises criterion) can be calculated as _______
Determine the maximum and minimum normal stress? Differentiate between them?
Help ASAP Determine the tensile stress in the upper plate at section b-b in mpa 3decimals
For the stress element shown below, which 2 points (σ, τ) in the stress domain could be used to define the diameter of the Mohr's Circle? (50 MPa, 25 MPa) (- 80 MPa, - 25 MPa) (- 80 MPa, 25 MPa) (50 MPa, - 25 MPa)