Suppose that P = 40 kN . (Figure 1) Part A Determine the principal stress developed at point A on the cross section of the beam at section a-a. Express your answers in ascending order separated by a comma using three significant figures. Figure < 1 of 1 TVO AZO n vec > 300 mm 01, 02 = MPa ja Submit Request Answer a 50 mm HA 150 mm Next > Provide Feedback 50 mm Section a-a

Suppose that P = 40 kN . (Figure 1) Part A Determine the principal stress developed at point A on the cross section of the beam at section a-a. Express your answers in ascending order separated by a comma using three significant figures. Figure < 1 of 1 TVO AZO n vec > 300 mm 01, 02 = MPa ja Submit Request Answer a 50 mm HA 150 mm Next > Provide Feedback 50 mm Section a-a

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.12P: A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the...

See similar textbooks

Similar questions

A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Determine the largest intensity of the distributed load ww and its length xx on the beam so that the beam remains in the horizontal position when it is loaded. Express your answers, separated by a comma, to three significant figures. Given: The rigid beam is supported at its ends by two A-36 steel tie rods. (Figure 1) The rods have diameters dAB=0.51 in.dAB=0.51 in. and dCD=0.29 in.dCD=0.29 in. The allowable stress for the steel is σallow=16.6 ksiσallow=16.6 ksi.
a) The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion) i) The second moment of area relative to z-axis, I_z, for the cross-section can be calculated as ( Enter your answer in cm4 ii) The bending stress at Point H can be calculated as (Enter your answer in MPa, Compressive stress is negative and tensile stress is positive) iii) The first moment of area required to calculate shear stress at H can be calculated as (Enter your answer in mm^3) iv) The absolute value of the transverse shear stress at point H can be calculated as (Enter your answer in MPa ) v) Maximum principal stress can be calculated as (Enter your answer in MPa ) vi) Minimum principal stress can be calculated as (Enter your answer in MPa ) vii) The equivalent stress for Maximum-Shear-Stress Theory ( Tresca criterion) (Enter your answer in MPa ) b) The von Mises equivalent stresses at point H can be calculated as: MPa c) The factors of safety at point H…
A solid aluminum shaft of 60 mm diameter fits concentrically in a hollow steel tube. The aluminum shaft carries an axial compressive load of 240 kN. Assume v = 1/3 and ESt = 70 GPa. Which of the following most nearly gives the minimum internal diameter of the steel tube so that no contact pressure exists? Which of the following most nearly gives the transverse strain? Which of the following most nearly gives the axial compressive stress in the aluminum?
Determine the limiting peripheral velocity of a steel ring if the allowable stress is 20 ksi the steel weighs 490lbm /ft^3 . What is the resulting stress if the ring rotates at 6500rpm ? Use r = 10in
A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal pressure of 15 N/mm2 and an external pressure of 5 N/mm2. Determine and sketch curves showing the distribution of the radial and circumferential stress across the section using Lame’s equations.
A mild steel shaft transmits P is 18 kW at N is 525 r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa.