Part A The 12-lb block has a speed of 4 ft/s when the force of F= (8t) lb is applied. The coefficient of kinetic friction at the surface is k = 0.2. (Figure 1) Determine the speed of the block when t = 3 s. Express your answer to three significant figures and include the appropriate units. HA ? v = Value Units Submit Request Answer Figure < 1 of 1 Provide Feedback v = 4 ft/s F = (8) lb

Part A The 12-lb block has a speed of 4 ft/s when the force of F= (8t) lb is applied. The coefficient of kinetic friction at the surface is k = 0.2. (Figure 1) Determine the speed of the block when t = 3 s. Express your answer to three significant figures and include the appropriate units. HA ? v = Value Units Submit Request Answer Figure < 1 of 1 Provide Feedback v = 4 ft/s F = (8) lb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.81P: Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center...

See similar textbooks

Similar questions

The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
consider the mass and pulley system in the attached file. mass m1 = 29 kg and mass m2 = 12kg. the angle of the inclined plane is given and the coefficient of kinetic friction between mass m2 and the inclined plane is uk = 0.12. assume the pulleys are massless and frictionless what is the acceleration of mass m2 on the inclined plane? take positive acceleration to be up the ramp a2 = ?
consider the mass and pulley system in the attached file. mass m1 = 29 kg and mass m2 = 12kg. the angle of the inclined plane is given and the coefficient of kinetic friction between mass m2 and the inclined plane is uk = 0.12. assume the pulleys are massless and frictionless when mass m2 moves a distance 4.94 m up the ramp, how far downward does mass m1 move? d= ?
1. If there is no friction between shaft AB and the collar, what angular velocity θ˙˙ must the mechanism have to keep the collar at r=300 mm from the vertical axis? Express your answer to three significant figures. 2. Consider the same mechanism again, with m=2.95 kg, d=225 mm, k=250 N/m, only now, instead of being smooth, the collar and shaft have a maximum coefficient of friction of μs=0.297. What is the minimum angular velocity required to keep the collar at a constant distance r=300 mm from the axis of rotation? Express your answer to three significant figures.
The arms of a Hartnell governor are of equal length. At the mid-position of the sleeve, theball arm is vertical and the radius at which the ball rotates is 10 cm when the equilibriumspeed is 400 RPM. On changing the speed by 1% the governor can overcome the frictionat this position. The friction force is assumed to have a constant value of 20 N at thesleeve. The sleeve moves ± 1.5 cm from the mean position. The minimum speed of thegovernor including friction is 450 rpm. The mass of the sleeve is 3.5 kg. Calculate themagnitude of rotating masses and initial compression of
1. A wheel tractor has a 200 HP engine. Calculate the available rimpull of this tractorif it is operating at an altitude of 1,000 m. above sea level, at an averagetemperature of 25oC, and at an average speed of 12 km/hr. Take rimpull efficiencyas 85%.2. The weight of the wheel tractor in Problem 1 is 30 tons and the weight on the drivingwheels is 50% of this weight. What is the maximum available rimpull if thecoefficient of traction is 0.25?3. What is the maximum grade that the tractor in Problems 1 and 2 can climb if it ismoving on a surface with a rolling resistance of 150 kg/ton?4. Assume that the tractor in Problems 1, 2, and 3 is moving down a 8% grade. Howmany minutes are necessary to accelerate to the average speed of 5 km/hr in firstgear? Use a rimpull reduction factor of 75% in your calculations.
The G weight of the figure, when descending, rotates the axis fixed to drums, which are supported by two cylindrical bearings of known dimensions, with known angular velocity ω. Determine the value of weight G, neglecting the rigidity and friction in the rope and assuming that the velocity diagram in the lubricant is linear. Given Data: μ = 8x10⁻² N/m², Di = 0.100 m,D = 0.02 m, Li = 0.1 m,De = 0.101 m, ω = 20/π rd/s
A cube with mass of m=80N is on the inclined plane with angle of phi=20 degrees. coeficient of static friction /mu_s = 0.25 coeficient of dynamic friction /mu_k = 0.15 Determine: what is the smallest size of the force F parallel to the inclined plane, which prevents the cube in the slide? what is the smallest size of the force F, which the cube starts to move along the inclined plane up? At what value of the force F starts the cube to rise at a constant speed?
1) Determine the average braking torque to be applied to stop the vehicle of mass 1.5 ton is movingdown the hill at a slope of 1:7 at 60 kmph and the vehicle is to be stopped at a distance of 50 m.Take the diameter of the vehicle tyre as 500 mm. If the friction energy is momentarily stored in a20 kg cast iron brake drum, what is the average temperature rise of the drum? The specific heat forcast iron may be taken as 520 J/kg ˚C.
A. A motorcycle and rider have a combined mass of 350kg. The wheels each have a mass of 20kg, diameter of 500mm and radius of gyration of 200mm. The rider accelerates uniformly from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. The average resistance to motion, including drag, is 105 N. 1. Determine the total work done as the motorcycle ascends the incline. 2. Calculate the amount of power developed during the climb. B. At another point in its journey, the motorcycle and rider travel at 80 km/h around a left-hand bend of radius 30m. Calculate: 1. The angular velocity of each of the wheels. 2. The moment of inertia of each wheel. 3. The magnitude and effect of the gyroscopic torque produced on the bike.
- 7 Maris A cycle tire a cartyre & a truck tire is revolving on the same road . Which one will experience more friction ? why ? explain the law for it -m - 2. Explain the type of friction in ice skating with a neat diagram . - 3. Explain redundant frame with equation