The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameterof 500 mm and a wall thickness of 6 mm. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 25 MPa.

The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameterof 500 mm and a wall thickness of 6 mm. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 25 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure tank shown is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown where β=55∘β=55∘. The tank has an inside diameter of 26.626.6 in.in. and a wall thickness of 0.3500.350 in.in. Determine the largest gage pressure that can be used inside the tank if the allowable normal stress perpendicular to the weld is 18.518.5 ksiksi and the allowable shear stress parallel to the weld is 8.58.5 ksiksi.
The pressure tank shown has an 8-mm wall thickness and butt-welded seams forming an angle β=20° with a transverse plane. For a gage pressure of 600 kPa, determine (a) the normal stress perpendicular to the weld, (b) the shearing stress parallel to the wel
A pressure-vessel head is fabricated by welding the circular plate to the end of the vessel as shown. If the vessel sustains an internal pressure of 450 kPa, determine the average shear stress in the weld and the state of stress in thewall of the vessel.
A cylindrical propane tank has an outside diameter of 3.25 m. If the allowable hoop stress is 100 MPa and the allowable axial or longitudinal stress is 45 MPa, determine the minimum thickness of the pipe when the internal pressure that can be applied to the tank is 1.25 MPa.
A cylindrical pressure vessel is fabricated from steel plates whichhave a thickness of 20 mm. The diameter of the pressure vessel is 500 mm andits length is 3m. Determine the maximum internal pressure which can be appliedif the stress in the steel is limited to 140 MPa.
The steel pressure tank shown has a 751 mm inner diameter and a 9.1 mm wall thickness.Knowing that the butt-welded seams form an angle ? = 50° with the longitudinal axis of thetank and that the gage pressure in the tank is 1.56 Mpa.a. Determine the normal stress perpendicular to the weldb. Determine the shearing stress parallel to the weld
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 556 mm2 and P= 36.79 kN. Round off the final answer to four decimal places.
A 4-ft diameter spherical tank is subjected to an internal pressure of 12 psf. If the wall thickness is 0.38", determine the tangential stress of the wall in psi.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and its length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa, and the circumferential stress is limited to 60 MPa.
The stress in thin-walled sphere is greater than the thin-walled cylinder. (A) True (B) False
For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.
A thick cylinder internal diameter 240mm external diameter240mm internal diameter ‘D’ is subject to external pressure of 50MPa. Determinethe diameter ‘D’ if the minimum hoop stress in the cylinder is not to exceed200MPa.