Part A The material for the 50-mm-long specimen has the stress- strain diagram shown. (Figure 1) If P = 150 kN is applied and then released, determine the permanent elongation of the specimen. Express your answer to three significant figures and include the appropriate units. HA ? &p = 0.775 mm

Part A The material for the 50-mm-long specimen has the stress- strain diagram shown. (Figure 1) If P = 150 kN is applied and then released, determine the permanent elongation of the specimen. Express your answer to three significant figures and include the appropriate units. HA ? &p = 0.775 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical specimen of aluminum having a diameter of 19 mm (0.75 in.) and length of 200 mm(8.0 in.) is deformed elastically in tension with a force of 48,800 N (11,000 lbf). Using the data inTable 6.1, determine the following:(a) The amount by which this specimen will elongate in the direction of the applied stress.(b) The change in diameter of the specimen. Will the diameter increase or decrease? (Complete Answer, Thank you)
PROPAGATION OF ERRORS Determine the range of values to which the strain will be calculated.F = 150000 +/- 150 lbfSide length = 1.2 +/- 0.025 inModulus of Elasticity = 25000 +/- 11.5 ksiDetermine the relative error. Is it above or below the accepted 5% relative error?
To determine the nominal or engineering stress and strain experienced by a specimen of a material while it is subjected to a tension test, and to be able to read important values from a conventional stress-strain diagram obtained from the test. A tension test is being conducted on a steel-rod specimen with a gauge length of L0=50 mm and initial diameter of d0=13 mm. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 506 MPa , e = 689 MPa , g = 585 MPa , and h = 0.146 mm/mm . A) Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 53.0 mm . B) Assuming that the stress is constant over the cross-sectional area and if the tension force used is P = 16.0 kN , find the nominal stress experienced by the rod. C)Determine the force P needed to reach the ultimate stress in the steel-rod specimen.
For a steel element with a 0.2% steel characteristic, a stress test was applied and the analysis of the data thrown by the material is required in terms of a variation of force and the respective deformations. Determine the following: A.Determine the percentage elongation at the point where the part develops the fracture. B.Construct the “Stress-Strain” diagram C.Maximum tensile strength of the part.
A small room is made up ofrectangular metal bars. One bar has a width of 10 mm and would beable to withstand a maximum compressive stress of 20 MPa.i. Prove that, the minimum breadth of this bar can withstand a burdenedwith a force of 3 KN.ii. If the bar in question is 2 m long and decreases in length by 0.25 mmwhen a force is applied, then show that a percentage strain can beobtained.iii. What would be its Modulus of Elasticity, E?
A cast iron cylinder has outside and inside diameter 200mm and 125mmrespectively. If the ultimate strength of cast iron is 150MPa calculate according to each of the following theories of failure the internal pressure that will cause fracture.(a) Maximum principal stress theory. (b) Maximum principal strain theory. (c) Maximum strain energy theory. Assume no longitudinal stress in the cylinder. Which of the results obtained you consider should be applied to this case. Take:µ = 0.25, σU = 150MPa. Ans: (a) 65.73MPa. (b) 59.24MPa, (c) 55.33MPa.
A tensile force of 10 kN is applied on a 0.02-m diameter and 2-m long rod. After applying theload, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. The lateral (transverse) strain is?
stress-strain behavior for the brass specimen shown in Figure 6.12, determine the following: (a) The modulus of elasticity (b) The yield strength at a strain offset of 0.002 (c) The maximum load that can be sustained by a cylindrical specimen hav- ing an original diameter of 12.8 mm (0.505 in.) (d) The change in length of a specimen originally 250 mm (10 in.) long that is subjected to a tensile stress of 345 MPa (50,000 psi)
A 11 in. inner diameter, 0.35 " wall thickness pipe is under a pressure of 2.5 ksi where strain gages installed along axial and circumferential directions register strains of 180 and 900 micro-strains (x10^-6), respectively. A) What is the Poisson's Ratio of this material and it's Elastic Modulus? B) In a uniaxial test, the pipe's material is observed to yield at a longitudinal strain of 0.1 in/in.in/in. Assuming a factor of safety of 2, the pipe can withstand impact energy of _______ lblb - in.in. per foot without suffering permanent deformation. C) If the pipe is depressurized and then subjected to a torque of 50 lblb - ft.ft., it will experience a shear strain of ________ rad.
Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
1.From the tensile stress-strain behavior for the brass specimen shown in below, determine the following: (a) The modulus of elasticity, (b) The yield strength at a strain offset of 0.002, (c) The maximum load that can be sustained by a cylinderical specimen having an original diameter of 12.8 mm, (d) The change in length of a specimen originally 250 mm long that is subjected to a tensile stress of 345 MPa.
A specimen is originally 1.5 ft long, has a diameter of 0.7 in., and is subjected to a force 550 lb. When the force is increased to 1900 lb, the specimen elongates 0.9 in. Determine the strain on the specimen and the modulus of the material. a. Strain Answer: _______ in./in. b. Modulus of Elasticity Answer: _______ ksi