Part b) A 25-mm-diameter shaft is pulled through a cylindrical bearing as shown in the figure below. The lubricant that fills the 0.3 mm gap between the shaft and bearing is an oil having a viscosity of 0.73 N.s'm. Determine the force F required to pull the shaft at a velocity of 3 m's. Assume the velocity distribution in the gap is lincar. Bearing Lubricant Shaft -0.5m Figure. Shaft and bearing

Part b) A 25-mm-diameter shaft is pulled through a cylindrical bearing as shown in the figure below. The lubricant that fills the 0.3 mm gap between the shaft and bearing is an oil having a viscosity of 0.73 N.s'm. Determine the force F required to pull the shaft at a velocity of 3 m's. Assume the velocity distribution in the gap is lincar. Bearing Lubricant Shaft -0.5m Figure. Shaft and bearing

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 900 N-m couple is applied to the flywheel in the diagram. The minimum force X required to prevent rotation of the flywheel is also applied. If the coefficient of belt friction is 0.20, a. which tension is larger, TA or TB?Explain b. What is the angle of contact in radians? c. What is the value of the ratio TA/TB?
A square plastic bar (length Lp, side dimensions p = 193 mm) is inserted inside a hollow,square, cast iron tube (length Lc = 400 mm, sidesc = 200 mm, and thickness tc = 3 mm). (a) What is the required initial length Lp of theplastic bar so that, when it is compressed bysome force P, the final length of bar and tube areequal to length Lc and, at the same time, the gapbetween plastic bar and cast iron tube is closed?(b) Compare initial and final volumes for theplastic bar.Assume that Ec =170 GPa, Ep = 2.1 GPa, vc = 0.3,and vp = 0.4.
A rod with a diameter of 13 mm and a length of 50 mm is subjected to a force of 50 kN. The diameter is reduced to 12.99265 mm. Determine: a. The modulus of elasticity. Answer: 200 GPa. b. Poisson's ratio. Answer: ν = 0.30 c. Shear modulus. Answer: G = 76.92 GPa. d. The deformation of the rod. Answer: δx = 0.09415 mm. Recommendation: Obtain the modulus of elasticity using the slope of the straight line.
The dimensions of a jib crane, which is manufactured by the Basick Co., are given in the figure. The crane has a mass of 800 kg and a center of mass at G. The bearing at A is a journal bearing and can support a horizontal force,whereas the bearing at B is a thrust bearing that supports both horizontal and vertical components. Determine the maximum load F that can be suspended from its end if the selected bearings at A and B can sustain a maximumresultant load of 24 kN and 34 kN, respectively.
Determine the magnitude of the resultant of the external forces, K(kips) *kips(k)- a unit of force, equivalent to 1000lbs. (Av, Ah, Bv). Add figure if necessary.
A rod of diameter 50 cm and length 6 m is hanging vertically and carries an axial loadof 10 kN at bottom end. Calculate the elongation of the bar at a distance 2 m from thebottom end. Take the unit weight of the rod material is 25 kN/m' and modulus ofelasticity of the material is 3x109 MPa.
A 0.1m3 volume of water is observed to be 0.0982m3 after a pressure is applied. What is the applied pressure? Use bulk modulus of elasticity of water is 2110MPa.
A shaft with a diameter of D = 80 mm and a length of L = 400 mm, shown in Fig is pulled with a constant velocity of U = 5 m/s the shaft rotates with a constant angular speed of n . = 1450 rpm in a bearing with variable diameter. The clearance between shaft and bearing, which varies from h1 = 1.2 mm to h2 = 0.4 mm, is filled with a Newtonian lubricant whose dynamic viscosity is 0.1 Pa⋅s. Determine the torque required to maintain the motion
An aluminum extrusion has the shape shown in the figure where b= 38 mm, d= 52 mm, a= 10 mm, and t= 2 mm. A vertical shear force of V= 2500 N acts on the cross section. Determine the shear flow that acts in the shape at points A–D. Part 1 Break the cross section into five rectangular areas, as shown. Find the area A1 of area (1) and the vertical distance y1 from the bottom edge of the cross-section to the centroid of area (1). Similarly, find the areas of the other four rectangles, and the vertical distance from the bottom edge of the cross section to the centroid of each. A1= 104 mm2 A2=A3= 20 mm2 A4=A5= 32 mm2 y1= 26 mm y2=y3= 5 mm y4=y5= 1 mm Part 2 Find y¯, the vertical distance from the bottom edge of the cross section to the centroid of the cross section. y¯= 14.27 mm Part 3 Find Iz, the area moment of inertia about the z centroidal axis for the cross-section. Iz=…
If the block is 1000kg, determine the value of frictional force if P is equal to 3200N. Usubstatic=0.50, Usubkinetic=0.35. A. 9810N B. 0 C. None of these D. 4905N
a 25mm flat bar shown in the figure is suspended vertically from the large end. If P=20 kN is applied at shown. Determine the change in the length of the bar
Engineering Mechanics (Like/Thumbs-up will be given. Write the solutions&FBD legibly. Include negative sign if in Compression, ex. -1,500 or if in Tension, ex. 1,500. Round to the nearest whole number.) The bucket and its load have a combined weight of 4000 lb with center of gravity at G. You may neglect the effect of the weights of the other members. Determine: A. Force in the hydraulic cylinder AB, in lb B. Magnitude of the pin reaction at O, in lb round off to two (2) decimal places