and where does it occur? The solid shaft shown is made of steel, (b) what is the angle of degrees between A and D? 165 N-m 50 N-m 440 N-m 55 N-m 30 mm 140 mm t B -0.9 m- 20 mm - 1.2 m 0.6 m Steel Modulus of Rigidity: G= 83, 000 MPa

and where does it occur? The solid shaft shown is made of steel, (b) what is the angle of degrees between A and D? 165 N-m 50 N-m 440 N-m 55 N-m 30 mm 140 mm t B -0.9 m- 20 mm - 1.2 m 0.6 m Steel Modulus of Rigidity: G= 83, 000 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A solid 1.500-in.-diameter steel [G = 12,000 ksi] shaft is subjected to torques TB = 270 lb-ft and TD= 95 lb-ft, acting in the directions shown. Assume a = 54 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 12 ksi, determine the maximum torque TC that can be applied to the shaft.
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied.
A hollow steel shaft 2660mm long is to be designed to transmit a torque of 24809kJ. Theshear modulus of elasticity, G = 82,740 GPa for steel. The total angle of twist of the lengthof the shaft is must not exceed 6 degrees. And the shear stress in the shaft must notexceed 110.32 MPa. What would be the ratio of the outside diameter to inside diameter?
A solid 1.250-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 295 lb-ft and TD= 95 lb-ft, acting in the directions shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 14 ksi, determine the maximum torque TC that can be applied to the shaft. [Answer: TC = 542 lb ft]
The following beam is supported by an aluminum bar at C, a steel bar at B, and a brass bar at D. The distance b is equal to 50 mm. The data is shown in the table:If the maximum rotation that can occur at point A is 0.25 radians clockwise, determine: a. The maximum force P that can be applied. Answ: 28347.97 kNb. The normal stress in the aluminum, steel, and brass bars. Answ: 25 000 MPa, 17500 MPa, 25937.5 MPa
For the shaft shown, a. Determine the maximum stress on the shaft and the maximum angle of twist of end D relative to end A. b. If the stress in every section must not exceed 25 MPa, what should be the uniform diameter of the shaft? dAB = 100mm, dbc = 80mm, dcd = 50mm G for the shaft is 80GPa. Consider clockwise torques as negative.
The solid steel shaft carries the torques T1= 1200 Nm and T2=750 N m. Using L1=L2=2.5 m and G = 83 GPa, determine: a. draw a diagram using a double headed arrows showing the torque in each segment b. determine the shear stresses in each segment and the angle of rotation of the free end if the diameter is 100 mm. c. the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 4^0.
The bronze shaft is formed by attaching a hollow shaft to a solid shaft. The allowable shear stress of bronze is 100 MPa. Use G = 35 GPa for bronze. a. If the torque applied is 15 kN m, determine the maximum shearing stress developed in the bronze shaft b. Determine the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 100 MPa or an angle of twist of 3.5 in the 3.5-m length.
A solid 1.500-in.-diameter steel shaft is subjected to torques TB = 205 lb-ft and TD= 135 lb-ft, acting in the directions shown. If the allowable shear stress in the shaft is 12 ksi, determine the maximum torque TC that can be applied to the shaft.
A two pinned end bars AB (Copper), ? = 850 ??2, ? = 120 ??? and BC (Aluminum), ? = 1000??2, ? = 70 ??? is subjected to a horizontal force of 100 ?? applied at pin B as shown in the figure, determine the horizontal displacement of pin B.
A solid constant-diameter circular shaft is subjected to the torques of TA = 460 lb·ft, TB = 1000 lb·ft, TC = 880 lb·ft, and TD = 340 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 7200 psi, what is the minimum acceptable diameter for the shaft?
The following beam is supported by three cables AD, BE, and CF. Cables AD and CF are made of steel, and cable BE is made of aluminum. The data is presented in the table. A force P of 125 kN is applied, and the temperature increases by 100°C. Determine: The stress in each cable. Answ: 25.09 MPa, 49.22 MPa. The vertical displacement of the beam. Answ: 1.99E-3 m.